Every RouterBOARD with a miniPCI-e slot which supports LTE modems can also be used as a LoRaWAN gateway by installing R11e-LoRa8 or R11e-LoRa9 card. Both UDP and LNS (starting with v7.12rc1 testing version) protocols are supported.
In order to work with Lora, IoT package should be installed. You can find the package for your device architecture in extra packages archive on the download page.
Starting with v7.11 (stable), LoRa functionality is moved into the IoT package that is available on the download page under extra packages. A separate Lora package is still available for download.
When using IoT package, LoRa functionality will move to a /iot lora
sub-menu. When using LoRa package, LoRa functionality will be possible via /lora
sub-menu.
LoRa package is not obligatory anymore and is left only for compatibility reasons.
Properties
Sub-menu: /iot lora
Property | Description |
---|---|
antenna-gain (integer [-128..127]; Default: 0) | Antenna gain in dBi. |
channel-plan (as-923 | au-915 | custom | eu-868 | in-865 | kr-920 | ru-864 | ru-864-mid | us-915-1 | us-915-2; Default: eu-868) | Frequency plans for various regions. |
disabled (yes | no; Default: yes) | Whether LoRaWAN gateway is disabled. |
forward (crc-disabled | crc-error | crc-valid; Default: crc-valid,crc-error) | Defines what kind of packets should be forwarded to Network server:
|
gateway-id (string) | Gateway ID or Gateway EUI, is used when registering the gateway with the server. |
lbt-enabled (yes | no; Default: no) | Whether gateway should use LBT (Listen Before Talk) protocol. |
listen-time (integer [0us..4294967295us]; Default: 5000us) | Time in microseconds to track RSSI before TX (used when lbt-enabled=yes). |
name (string; Default: ) | Name of LoRaWAN gateway. |
network (private | public; Default: public) | Whether sync word should (network=private) or should not (network=public) be used. |
rssi-threshold (integer [-32,768 .. 32,767]; Default: -65dB) | RSSI value to determine whether forwarder may use specific channel to talk. If RSSI value is below rssi-threshold, channel could be used (used when lbt-enabled=yes). |
servers (list of string; Default: ) | Name or names of servers from /lora servers. |
src-address (IP; Default: ) | Specifies uplink packet source address if necessary (address should match an address configured on the RB). |
spoof-gps (string; Default: ) | Set custom GPS location:
|
Channels
Sub-menu: /iot lora channels
Property | Description |
---|---|
bandwidth (7.8_kHz | 15.6_kHz | 31.2_kHz | 62.5_kHz | 125_kHz | 250_kHz | 500_kHz; Default: 125_kHz) | Bandwidth of specific channel, predefined when any of channel-plan preset is used, but could be manually changed when channel-plan is set to custom. |
disabled (yes | no; Default: no) | Disable or enable the channel. |
freq-off (integer [-400000..400000]; Default: ) | Channel frequency offset against radio central frequency, it makes possible to adjust channel frequencies so that channels does not overlap. |
radio (radio0 | radio1; Default: ) | Defines which radio uses selected channel. |
spread-factor (SF7 | SF8 | SF9 | SF10 | SF11 | SF12; Default: ) | Defines the Spread Factor for a channel with type=LoRa. Lower Spread Factor means higher data rate. |
To view current channels, issue the command /iot lora cannels print
:
/iot lora channels print Columns: NAME, TYPE, RADIO, FREQ-OFF, BANDWIDTH, FREQ, SPREAD-FACTOR, DATARATE # NAME TYPE RADIO FREQ-OFF BANDWIDTH FREQ SPREAD-FACTOR DATARATE 0 gateway-0 MSF radio1 -400000 125_kHz 868.1 1 gateway-0 MSF radio1 -200000 125_kHz 868.3 2 gateway-0 MSF radio1 0 125_kHz 868.5 3 gateway-0 MSF radio0 -400000 125_kHz 867.1 4 gateway-0 MSF radio0 -200000 125_kHz 867.3 5 gateway-0 MSF radio0 0 125_kHz 867.5 6 gateway-0 MSF radio0 200000 125_kHz 867.7 7 gateway-0 MSF radio0 400000 125_kHz 867.9 8 gateway-0 LoRa radio1 -200000 250_kHz 868.3 SF7 9 gateway-0 FSK radio1 300000 125_kHz 868.8 50000
Channels are created using freq-off
and radio's center-freq
frequencies. To view radios central frequency use the command /iot lora radios print
.
To understand how each channel's frequency is calculated, check the example below:
# NAME TYPE RADIO FREQ-OFF BANDWIDTH FREQ SPREAD-FACTOR DATARATE 0 gateway-0 MSF radio1 -400000 125_kHz 868.1
radio1
is selected to be used for channel #0 and it is configured with center-freq=868500000
(868500000 Hz or 868.5 MHz).
By using frequency offset, freq-off=-400000
(-400000 Hz or -0.4 MHz), we define channel #0 to be 868500000-400000=868100000
Hz or 868.1 MHz.
To configure custom channels, select "custom" channel profle with the help of the command:
/iot lora set [find] channel-plan=custom
Join EUI
The gateway will forward to the server every single LoRaWAN payload it receives. That includes neighboring LoRaWAN node's payloads as well. It might not be ideal to forward everything, as, for example, it can increase the data amount used (and directly impact ISP plan cost).
The Join EUI menu allows you to specify a range of Join EUI's that the gateway will forward. After adding the range, make sure to apply it to the server settings.
If the Join EUI of the packet does not match the configuration, the packet is not forwarded to the server.
You can find the Join EUI used by your node with the help of RouterOS GUI. Go to the "LoRa" section and to the "Traffic" sub-menu (which is only available using the graphical interface). After you power your LoRaWAN node, the node should send a "Join-request" packet. Double-click on it to inspect it:
Sub-menu: /iot lora joineui
Property | Description |
---|---|
joineui (string; Default: ) | Define a range of Join EUI's. |
name (string; Default: ) | Define the name for the range. |
An example of Join EUI would look like this E0 E1 E2 01 02 03 04 05. It consists of 8 octets in HEX format.
To add a range that allows every possible Join EUI, add a filter like this:
/iot lora joineui add name=ALL joineuis=0000000000000000-ffffffffffffffff
To add a range that allows "nothing" (basically "restrict" all Join EUI's), add a filter like this:
/iot lora joineui add name=NONE joineuis=0000000000000000-0000000000000000
For a specific single Join EUI, add a filter like this:
/iot lora joineui add name=SINGLE joineuis=E0E1E20102030405-E0E1E20102030405
Network ID
The gateway will forward to the server every single LoRaWAN payload it receives. That includes neighboring LoRaWAN node's payloads as well. It might not be ideal to forward everything, as, for example, it can increase the data amount used (and directly impact ISP plan cost).
The NetID menu allows you to specify a list of NetIDs that the gateway will forward. After adding the list, make sure to apply it to the server settings.
If the NetID (DevAddr range) of the packet does not match the configuration, the packet is not forwarded to the server.
NetIDs define the ranges of Device Addresses (DevAddr) that were assigned to different operators/servers by the LoRaWAN Alliance. A list with most ranges can be found in the TTN guide.
DevAddr is assigned to the LoRaWAN node by the LoRaWAN server after the communication with the server takes place. For example, TTN will assign your node an address from within the range 26000000 - 27FFFFFF. You can find it under the LoRaWAN server dashboard or using RouterOS GUI, under the "Traffic" sub-menu (after "join-request" and "join-accept" communication takes place) in the Dev Addr column/field.
Let's say TTN assigned 26 1B D8 D1 Dev Addr to your node. Based on the TTN guide, it falls under the 26000000 - 27FFFFFF DevAddr range and it belongs to the 000013 NetID.
Sub-menu: /iot lora netid
Property | Description |
---|---|
netids (string; Default: ) | Define the NetIDs |
name (string; Default: ) | Define the name for the ID. |
To add a filter for a specific NetId, use the command (you can add more than one using a "comma" separator):
/iot lora netids add name=TTN netids=000013
Servers
Sub-menu: /iot lora servers
There are a few predefined servers that can be used (it requires to make an The Things Network account to use them):
[admin@MikroTik] /iot/lora/servers> print Columns: NAME, UP-PORT, DOWN-PORT, ADDRESS # NAME UP-PORT DOWN-PORT ADDRESS 0 TTN-EU 1700 1700 eu.mikrotik.thethings.industries 1 TTN-US 1700 1700 us.mikrotik.thethings.industries 2 TTS Cloud (eu1) 1700 1700 eu1.cloud.thethings.industries 3 TTS Cloud (nam1) 1700 1700 nam1.cloud.thethings.industries 4 TTS Cloud (au1) 1700 1700 au1.cloud.thethings.industries 5 TTN V3 (eu1) 1700 1700 eu1.cloud.thethings.network 6 TTN V3 (nam1) 1700 1700 nam1.cloud.thethings.network 7 TTN V3 (au1) 1700 1700 au1.cloud.thethings.network
Custom servers can be added as well. Data forwarding to multiple servers can work simultaneously if the first server does not change "DevAdress" part of the packet and under the condition that all servers are able to decode the packet.
Property | Description |
---|---|
address (domain name or IP address; Default: ) | Defines LoRaWAN Network server address. |
name (string; Default: ) | Defines server name. |
protocol (UDP | LNS | CUPS; Default: UDP) | Specify whether to use UDP, LNS or CUPS protocol for the communication with the LoRaWAN server. |
down-port (integer [0..65535]; Default: 1700) | Parameter that is used when UDP protocol is selected. Defines port for down-link communication (from server to node) with LoRaWAN Network server. Most of known open source servers uses port 1700 as default, but it can change if multiple servers are configured on the same machine. |
up-port (integer [0..65535]; Default: 1700) | Parameter that is used when UDP protocol is selected. Defines port for up-link communication (from node to server) with LoRaWAN Network server. Most of known open source servers uses port 1700 as default, but it can change if multiple servers are configured on the same machine. |
netid (list of string; Default: ) | Parameter that is used when UDP protocol is selected. Applies a filter to only send LoRaWAN payloads that match the Network ID (Net ID) filter configured. |
joineui (list of string; Default: ) | Parameter that is used when UDP protocol is selected. Applies a filter to only send LoRaWAN payloads that match the Join EUI filter configured. |
port (integer [0..65535]; Default: 8887) | Parameter that is used when LNS or CUPS protocol is selected. For LNS, defines the WSS (WebSocket) port and, for CUPS, defines HTTPS port. |
key (string; Default: ) | Parameter that is used when LNS or CUPS protocol is selected. Specify the LoRa Basics Station LNS Authentication Key or CUPS API KEY (both generated on the server). |
ssl (yes or no; Default: no) | Parameter that is used when LNS or CUPS protocol is selected. Specify whether to use or not to use SSL (if the server supports TLS server authentication). When this option is choosen, root SSL certificate(s) must be uploaded under the certificates menu. |
certificate (list of string; Default: none) | Parameter that is used when LNS or CUPS protocol is selected. Select an uploaded client certificate (if the server awaits TLS client authentication). If TLS client authentication is not required by the server, use the default "none" setting. |
interval (integer [0..65535]; Default: ) | Parameter that is used when CUPS protocol is selected. Specify the interval with which the LoRa Basics Station will query CUPS server for configuration updates/changes. |