...
After the banner can be printed other important information, like /system note set by another admin, the last few critical log messages, demo version upgrade reminder, and default configuration description.
...
| Code Block | ||||
|---|---|---|---|---|
| ||||
[admin@MikroTik] > interface [enter] [admin@MikroTik] /interface> / [enter] [admin@MikroTik] > |
Use up arrow to recall previous commands (if this is a multiline command, then you can press F8 in order to expand it) from command history (commands that added sensitive data, like passwords, will not be available in the history), TAB key to automatically complete words in the command you are typing, ENTER key to execute the command, Control-C to interrupt currently running command and return to prompt and ? to display built-in help, in RouterOS v7, F1 has to be used instead.
The easiest way to log out of the console is to press Control-D at the command prompt while the command line is empty (You can cancel the current command and get an empty line with Control-C, so Control-C followed by Control-D will log you out in most cases).
...
Item numbers are assigned by the print command and are not constant - it is possible that two successive print commands will order items differently. But the results of the last print commands are memorized and, thus, once assigned, item numbers can be used even after add, remove and move operations (since version 3, move operation does not renumber items). Item numbers are assigned on a per session basis, they will remain the same until you quit the console or until the next print command is executed. Also, numbers are assigned separately for every item list, so /ip address print will not change the numbering of the interface list.
...
| Property | Description |
|---|---|
| add | This command usually has all the same arguments as a set, except the item number argument. It adds a new item with the values you have specified, usually at the end of the item list, in places where the order of items is relevant. There are some required properties that you have to supply, such as the interface for a new address, while other properties are set to defaults unless you explicitly specify them. Common Parameters
Return Values
|
| edit | This command is associated with the set command. It can be used to edit values of properties that contain a large amount of text, such as scripts, but it works with all editable properties. Depending on the capabilities of the terminal, either a full-screen editor or a single line editor is launched to edit the value of the specified property. |
| find | The find command has the same arguments as a set, plus the flag arguments like disabled or active that take values yes or no depending on the value of the respective flag. To see all flags and their names, look at the top of the print command's output. The find command returns internal numbers of all items that have the same values of arguments as specified. |
| move | Changes the order of items in the list. Parameters:
|
hows Shows all information that\'s accessible from a particular command level. Thus, /system clock print shows the system date and time, /ip route print shows all routes etc. If there\'s a list of items in the current level and they are not read-only, i.e. you can change/remove them (example of read-only item list is /system history, which shows a history of executed actions), then print command also assigns numbers that are used by all commands that operate with items in this list.Common Parameters:
| |
| remove | Removes specified item(-s) from a list. |
| set | Allows you to change values of general parameters or item parameters. The set command has arguments with names corresponding to values you can change. Use ? or double Tab to see a list of all arguments. If there is a list of items in this command level, then the set has one action argument that accepts the number of items (or list of numbers) you wish to set up. This command does not return anything. |
...
- Normal mode - indicated by normal command prompt.
- Safe mode - safe mode is indicated by the word SAFE after the command prompt. In this mode, the configuration is saved to disk only after the safe mode is turned off. Safe mode can be turned on/off with Ctrl+cX or F4. Read more >>
- Hot-lock mode - indicated by additional yellow >. Hot-lock mode autocompletes commands and can be turned on/off with Ctrl+v F7
Quick Typing
There are two features in the console that help entering commands much quicker and easier - the [Tab] key completions, and abbreviations of command names. Completions work similarly to the bash shell in UNIX. If you press the [Tab] key after a part of a word, the console tries to find the command within the current context that begins with this word. If there is only one match, it is automatically appended, followed by a space:
...
| Key | Description |
|---|---|
| Control-C | keyboard interrupt |
| Control-D | log out (if an input line is empty) |
| Control-K | clear from the cursor to the end of the line |
| Control-U | clear from the cursor to the beginning of the line |
| Control-X or F4 | toggle safe mode |
| Control-VF7 | toggle hot lock mode mode |
| Control-R or F3 | toggle console search |
| F6 | toggle cellar |
| F1 or ? | show context-sensitive help. If the previous character is \, then inserts literal ?. |
| Tab | perform line completion. When pressed a second time, show possible completions. |
| # | Send a message to an internal chat system |
| Delete | remove character at the cursor |
| Control-H or Backspace | remove removes character before cursor and move moves the cursor back one position. |
| Control-\ | split line at cursor. Insert newline at the cursor position. Display second of the two resulting lines. |
| Control-B or Left | move cursor backward one character |
| Control-F or Right | move cursor forward one character |
| Control-P or Up | go to the previous line. If this is the first line of input then recall previous input from history. |
| Control-N or Down | go to the next line. If this is the last line of input then recall the next input from the history |
| Control-A or Home | move the cursor to the beginning of the line. If the cursor is already at the beginning of the line, then go to the beginning of the first line of the current input |
| Control-E or End | move the cursor to the end of the line. If the cursor is already at the end of the line, then move it to the end of the last line of the current input |
| Control-L or F5 | reset terminal and repaint screen |
...