Label Range and TTL
From the /mpls settings
menu it is possible to assign specific dynamic label range and TTL propagation. If for some reason static label mapping is used then the dynamic range can be adjusted to exclude statically assigned label numbers from being dynamically assigned by any of the label distribution protocols.
Property | Description |
---|---|
dynamic-label-range (range of integer[16..1048575]; Default: 16-1048575) | Range of Label numbers used for dynamic allocation. The first 16 labels are reserved for special purposes (as defined in RFC). If you intend to configure labels statically then adjust the dynamic default range not to include numbers that will be used in a static configuration. |
propagate-ttl (yes | no; Default: yes) | Whether to copy TTL values from IP header to MPLS header. If this option is set to no then hops inside the MPLS cloud will be invisible from traceroutes. |
allow-fast-path(yes | no; Default: yes) | Enable/disable MPLS fast-path support. |
MPLS MTU
Configuration of MPLS MTU (path MTU + MPLS tag size) is useful in cases when there is a large variety of possible MTUs along the path. Configuring MPLS MTU to a minimum value that can pass all the hops will ensure that the MPLS packet will not be silently dropped on the devices that do not support big enough MTU.
MPLS MTUs are configured from the /mpls interface
menu.
Code Block | ||||
---|---|---|---|---|
| ||||
[admin@rack1_b35_CCR1036] /mpls/interface> print Flags: X - disabled; * - builtin 0 ;;; router-test interface=ether1 mpls-mtu=1580 input=yes 1 ;;; router-test interface=ether2 mpls-mtu=1580 input=yes 2 interface=all mpls-mtu=1500 |
...
Read more on MTUs in the MTU in RouterOS article.
Forwarding Table
Sub-menu: Entries in the /mpls forwarding-table
Entries in this sub-menu show menu show label bindings for specific routes that will be used in MPLS label switching. Properties in this menu are read-only
...
.
...
Code Block | ||||
---|---|---|---|---|
|
- label - egress MPLS label
- nh - out next-hop IP address
- interface - out the interface
...
Code Block | ||
---|---|---|
| ||
[admin@rack1_b35_CCR1036] /mpls/forwarding-table> print Flags: L, V - VPLS Columns: LABEL, VRF, PREFIX, NEXTHOPS # LABEL VRF PREFIX NEXTHOPS 0 L 16 main 10.0.0.0/8 { nh=10.155.130.1; interface=ether12 } 1 L 18 main 111.111.111.3 { label=impl-null; nh=111.12.0.1; interface=ether2 } 2 L 17 main 111.111.111.2 { label=impl-null; nh=111.11.0.1; interface=ether1 } |
Property | Description |
---|---|
prefix (IP/Mask) | Destination prefix for which labels are assigned |
label (integer) | Ingress MPLS label |
ldp (yes | no) | Whether labels are LDP signaled |
nexthops () | An array of the next-hops, each entry in the array represents one ECMP next-hop. Array entry can contain several parameters:
|
out-label (integer) | Label number which is added or switched to for outgoing packet. |
packets (integer) | Number of packets matched by this entry |
te-sender | |
te-session | |
traffic-eng | Shows whether the entry is signaled by RSVP-TE (Traffic Engineering) |
type (string) | Type of the entry, for example, "vpls", etc. |
vpls (yes | no) | Shows whether the entry is used for VPLS tunnels. |
vpn | |
vrf | Name of the VRF table this entry belongs to |