Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

The device accepts power from the USB port of the RouterBOARD device.

Setup

...

First startup

Connect your Woobm-USB to the USB port

...

Configuration

The Woobm runs a special operating system where you can configure its basic functionality, the configuration is accessible through a web interface. To connect to the RouterBOARD device, the following methods are available:

  1. Click on "Terminal" in the Woobm web configuration interface.
  2. Open a Telnet connection to the Woobm device from your computer, you will be directly connected to the RouterBOARD device.

For more detailed instructions, please see full Woobm software documentation on https://mt.lv/help

Buttons and jumpers

The Woobm has one button, which has the following functions:

...

, open a wireless network with SSID: WoobmAP will be created. Connect to device and open device IP address in a web browser.

Warning

Default Woobm-USB IP is 192.168.4.1

A device running RouterOS will automatically mount as a serial USB device and provide access after successful login.

WEB interface

WEB interface allows access to the serial port from devices equipped with an 802.11b/g/n 2.4GHz wireless module.

Image Added

Web interface default page is "Home" From the home page, it is possible to connect and configure RouterOS neighbor devices (MikroTik devices in the same network) Press on a device IP address to establish a connection:

Image Added

By opening the Terminal tab, Woobm-USB will try to emulate the USB serial interface. On a successful attempt "Connection successful! " message will appear above the terminal window. You can enter commands from the keyboard or use key buttons to send out commands through the USB serial interface.

Show keyboard will bring up the keyboard on mobile devices. Extra buttons provide missing keyboard keys for mobile devices.

Note

By opening the Terminal tab, Woobm-USB will try to emulate the USB serial interface. On a successful attempt "Connection successful! " message will appear above the terminal window. You can enter commands from the keyboard or use key buttons to send out commands through the USB serial interface.

Show keyboard will bring up the keyboard on mobile devices. Extra buttons provide missing keyboard keys for mobile devices.

Settings

Settings tab provides basic configuration for Woobm-USB device. The basic settings part provide serial port, button, LED, and wireless general settings

Image Added

Properties

PropertyDescription
Identity (string; Default: Mikrotik)Device identity is used for the DHCP client as the 'hostname' parameter when reporting it to the DHCP server and for neighbor discovery.
Telnet port (integer; Default: 23)Port used for incoming telnet requests
Baud-rate (integer; Default: 115200)Baud rate used for serial communication. Should match a host device.
Data bits (; Default: 8)
Parity (; Default: None bits)
Stopbits (integer; Default: 1)
Web conn. timeout (integer; Default: 2400)
WPS enabled (On/off; Default: On)
Set the default settings with a button (On/off; Default: On)
Device greeting (On/off; Default: On)
Force echo (On/off; Default: On)
Ignore telnet commands (On/off; Default: On)
Status LEDs enabled (On/off; Default: On)
802.11 mode (; Default: default)

WiFi Station settings part provides settings wireless for Woobm-USB in client mode.

Image Added

PropertyDescription
SSID (string; Default: )Provide SSID of nearby Access Point, or use scan function.
Password (string; Default: )WPA-PSK and WPA2-PSK
SSID MAC (MAC; Default: )
Station MAC (MAC; Default: )
IP address (IP; Default: )
Gateway (IP; Default: )
Netmask (IP; Default: )

WiFi AP settings part provides wireless settings for Woobm-USB in Access Point mode.

Image Added

PropertyDescription
SSID (string; Default: )SSID of Woobm-USB Access Point
Password (string; Default: )WPA-PSK and WPA2-PSK
Channel (; Default: 6)Wireless channel used for AP
Auth. mode (; Default: )
Hidden (On/Off; Default: Off)
Max conn (1 to 4; Default: 4)Maximum allowed clients to Access Point.
Beacon interval (100 to 60000; Default: 100)How often Access point broadcasts AP information.
IP address (IP; Default: 192.168.4.1)
Gateway (IP; Default: )
Netmask (IP; Default: )
AP MAC (MAC; Default: )
DHCP Enabled (On/Off; Default: On)Enable/disable DHCP server
IP range start (IP; Default: 192.168.4.2)
IP range end (IP; Default: 192.168.4.5)
IP lease time (; Default: 120)

Upgrade firmware

Use the upgrade firmware tab for manual firmware upgrade. Firmware is available in the Product Support & Download section on our web page.

Telnet access

It's possible to use Telnet clients to access the serial port. For Telnet access open Woobm-USB address in telnet client. Woobm-USB forwards serial port to telnet client.

Note

Only one instance of the serial port bridge may be emulated.

Button functionality

Button provides functionality for enabling WPS, reset configuration and send out a neighbor message (MNDP).

WPS mode

If a button is pressed for less than 5 seconds - WPS mode is enabled. If a connection is made to the Access point - the Woobm station configuration is saved and old data is overwritten.

Reset configuration

To reset configuration:

1) Woobm should be unplugged (removed from the USB port);

2) Press and hold the button;

3) Attach Woobm to the USB port while holding the button;

4) Wait till the red LED light starts blinking;

5) Release button;

The device will reset be reset to the default configuration.

Neighbor message

The neighbor message is sent out automatically every minute. To send a message out manually hold the button for at least 5 seconds until the LED light stops blinking.

Operating system support

 The device supports Woobm software only. It can be updated, by uploading a newer.BIN file through the web configuration page.


Federal Communication Commission Interference Statement

ModelFCCID
Woobm-USBTV7WBM

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

...

Innovation, Science and Economic Development Canada

ModelIC
Woobm-USB7442A-WBM

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

...

CAN ICES-003 (B) / NMB-003 (B)

IMPORTANT: Exposure to Radio Frequency Radiation.
This equipment complies with the IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and any part of your body.
Cet équipement est conforme aux limites d'exposition au rayonnement IC définies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et toute partie de votre corps.

...

UKCA marking

Eurasian Conformity Mark

Частотный диапазон

Мощность передатчика

2412-2472 МГц

≤100 мВт

*Доступные частотные каналы могут различаться в зависимости от модели продукта и сертификации. 

...

Изготовитель: Mikrotikls SIA, Aizkraukles iela 23, Riga, LV-1006, Латвия, support@mikrotik.com. Сделано в Китае, Латвии или Литве. Cм. на упаковке.

Для получения подробных сведений о гарантийном обслуживании обратитесь к продавцу. Информация об импортерах продукции MikroTik в Российскую Федерацию: https://mikrotik.com/buy/europe/russia

Продукты MikroTik, которые поставляются в Евразийский таможенный союз, оцениваются с учетом соответствующих требований и помечены знаком EAC, как показано ниже:

...

Por favor contacte a su distribuidor local para preguntas regionales específicas. La lista de importadores se puede encontrar en nuestra página de inicio – https://mikrotik.com/buy/latinamerica/mexico.



The National Commission for the State Regulation of Communications and Informatization by Ukraine

...

CE Declaration of Conformity

Manufacturer: Mikrotikls SIA, Brivibas gatve 214i Riga, Latvia, LV1039.

Hereby, Mikrotīkls SIA declares that the

...

Woobm-USB is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://mikrotik.com/productsImage Modified

Frequency bands terms of use

Frequency range (for applicable models)

Channels used

Maximum Output Power (EIRP)

Restriction

2412 - 2472 MHz

1 - 13

20 dBm

Without any restriction to use in all EU Member States

* It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed!


Info
Note. The information contained here is subject to change. Please visit the product page on www.mikrotik.com for the most up to date version of this document.