...
- Yellow - partially working
- Green - Working
- Red - Not working at the moment
0Beta7| v7.1Beta1 | v7.1Beta2 | v7.1Beta3 | v7.1Beta4 | v7.1rc1 | v7.1rc2 | v7.1rc3 | v7.1rc5 | v7.1rc6 | | 1 |
|---|
| Winbox |
|
| BGP support |
|
| OSPF support |
|
| RIP support |
|
| Router ID support |
|
| Routing filter support |
Sets rule as string |
|
|
|
| Generic |
|
| /31 address support | N/A |
| Convert route rules after upgrade from v6.x |
N/A | OK |
|
| Static IPv6 upgrade from ROS v6 |
NOK | OKOK | NOKOK | OK | OK | OKOK |
|
| recursive route over ipv6 LL address |
OK |
|
| 3 level recursive gateway with ECMP |
OKOKN/AOK |
|
| Addresses from same subnet to multiple interfaces |
NOK| N/A |
| Show time when route was last updated | N/A |
| Check Gateway |
Ping OK, ARP NOK (works as ping), BFD NOK (not implemented) | OKOK | NOK (Added but does not work at the moment) | OKDoes not NOK (wrong src is picked for locally originated packets) | | Does not work correctly with /32 addresses |
| Routing-table parameter for ping and telnet |
NOK |
|
| Show if route is hardware accelerated |
N/A | | Shows if route is candidate for HW acceleration |
| Custom route selection policy |
N/A |
|
| IPv4 with IPv6 nexthops and RFC5549 |
N/A | OK | Routing Instance | OK | Renamed to Router-ID | VRF | Needs more testing |
|
|
|
| Routing id |
|
| VRF |
|
| Management services support for VRFs |
N/A | telnet, ssh, api, www services can be set to listen on specific VRF |
| Some kind of mechanism to import/export routes from one vrf to another within same router | N/A |
| BFD | N/A |
|
|
| OSPF |
|
| Convert OSPF config from v6 to v7 after upgrade |
N/A | Known conversion problems: - NBMA neighbors place in backbone
ospf-v2 networks + interface may have issues dynamic interfaces may have issues MPLS PE CE features are not converted
|
| OSPF neighbors in NSSA Area |
Cannot establish adjacency | OSPF with
|
| OSPF in broadcast network |
Does not work with more than 2 neighbors | OK | | OSPF with routing filters |
OKOKN/A |
|
| HMAC-SHA auth RFC5709 | N/A |
| BGP and OSPF SNMP monitoring | N/A |
|
|
| BGP |
|
| Convert BGP config from v6 to v7 after upgrade |
N/A | OK |
|
| BGP Templates and dynamic peers |
OK |
|
| BGP connect listen on a network |
OKOK |
|
| Show from which peer route received | OK ( /routing/route/print detail --> belongs-to) |
| BGP Address Families |
Currently only IPv4, IPv6 | Does not work right after peer established, need to resend routesOKOKOK |
|
| BGP Local address auto selection |
OK | OKOK | BGP OK | | BGP peer-cache uptime in "established" state | N/A |
|
|
| BGP Flow Spec | Flow spec attributes are forwarded |
| BGP Selection |
OK |
|
|
|
| BGP Selection (Multipath) | N/A |
| BGP Confederation |
OK |
|
| BGP Aggregation | N/A |
| BGP ORF | N/A |
| Discard prefix RTBH RFC 6666 | N/A |
| AS-wide Unique BGP Identifier RFC 6286 | N/A |
| Exported PDU PCAP saver |
Ok |
|
| Exported PDU PCAP loader |
|
|
|
| MPLS |
|
| Static label mapping |
N/A |
|
| Static mapping upgrade from v6 |
|
| LDP IPv4 mapping |
N/A | Ok | N/AN/A | Ok |
|
| LDP config upgrade from v6 |
N/A | N/A |
|
| TE Config upgrade from v6 |
N/A | N/A | N/A |
|
| VPLS config upgrade from v6 |
N/AN/A | N/A | N/A |
|
| Ability to use MPLS EXP-bit in Queues | N/A |
| MPLS Fast-Path | N/A |
|
|
| RPKI session |
OK |
|
| RPKI possibility to view received info of specific prefix |
N/A | OK |
|
| RPKI show connection status |
N/AOk |
|
|
|
| Filters |
|
| Convert routing filters after upgrade from v6.x |
N/Asome as-path matching regexps may not be upgraded | N/ACompletion works but needs fine-tuning |
|
| Routing filter chain drop by default without rules |
OK |
|
| Routing filter prefix match |
OK |
|
| Routing filter protocol match |
Missing other protocols like modem DHCP etc (these routes are not matched by "static") | |
|
| Routing filter append communities |
|
| Routing filter append large community |
Routing filter append communities | OK | Routing filter append large community | OK |
|
| Routing filter set weight |
"sub, add" does not work if attribute has default unset value, if attribute is not set then default value should be assumed. | Routing filter set MED | "sub,add" should assume default value.
|
| Routing filter set local pref |
"sub, add" does not work if attribute has default unset value, default value should be 100 if not set. | | Routing filter set MED |
|
| Routing filter set origin |
OK |
|
| Routing filter set igp metric from OSPF cost |
Can be set with set-num-prop=bgp-igp-metric<add>ospf-ext-metric or ospf-metric, but what to do if it is not possible to guess which metric to use? |
|
| Routing filter match prefix with address list |
OK |
|
| Routing filter match community/large community lists |
OK |
|
| Routing filter add prefix to address list | N/A |
| Routing filter validate prefix with RPKI |
OKN/A
Performance Status
Used hardware:
...