...

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing accidents.
Ultimate disposal of this product should be handled according to all national laws and regulations.
All installation methods for mounting an access point on any wall surface is are subject to the acceptance of local jurisdiction.
The Installation of the equipment must comply with local and national electrical codes.
This product is intended to be mounted outdoors on a pole. Please read the mounting instructions carefully before beginning installation. Failure to use the correct hardware and configuration or to follow the correct procedures could result in a hazardous situation for people and damage to the system.
Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.
Read the installation instructions before connecting the system to the power source.
We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your own risk!
In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.

...

• Open the Ethernet port door;
• Insert the SIM card into the slot, with the chip facing UP;
• Connect the device to the included PoE injector with Ethernet cable to the data+power end;
• Connect the data end of the PoE injector into to the computer;
• Connect the power adapter to the PoE injector;
• Open the https://192.168.88.1 in your web browser;
• User name: admin, and there is no password;
• Use the check for update option to upgrade the device to the latest version. You must have an active SIM card with available data;
• The device will reboot;
• Connect again and in the QuickSet menu set your country, to apply country regulation settings;
• Secure your device and set a strong password.

Powering

The device accepts 1012-28 57 V DC input from passive Power over Ethernet injectors. The device does not work with IEEE802.3af compliant 48 V power injectors. A PoE injector is included in the package.
Maximum power consumption 8 6 W.
Connecting to a PoE Adapter:

...

The device is compatible with standard offset dishes. Assemble Ethernet cable with cover as shown on in the illustration:

• Rubber The rubber seal has been cut on the side so you can attach it to the Ethernet cable. It needs to be inside the Housing nut when assembling the compression nut will compress it to the Ethernet cable.

...

• Attach the unit to your dish, LDF mounting diameter is 40 mm. Please, ensure to placement with an arrow facing upwards.
  
• Plugin Ethernet cable and tighten the cover by screwing it clockwise.

The device is designed to be used outdoors and mounted on the dish, with an Ethernet cable connecting to the back of the unit.
Please ensure to mount the LDF unit on the offset mount in the proper position - the unit facing upwards to the dish.
The dish will act as a reflector, amplifying the signal. The final position of your assembly should be placed and installed on the pole. For pole mounting instructions please refer to your dish mounting instructions.
Please ensure that the cable feed is pointing downwards.
The IPX rating scale of this device is IP54.

Mounting The mounting and configuration of this device should be done by a qualified person.

Sim slot usage

Extension slots and ports

• One Ethernet port, supporting supports automatic cross/straight cable correction (Auto MDI/X), so you can use either straight or cross-over cables for connecting to other network devices.
• MiniPCIe slot with an integrated modem.
• Mode button.

...

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

...

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna must not be co-located or operation operated in conjunction with any other antenna or transmitter.
IMPORTANT: Exposure to Radio Frequency Radiation.
This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and any part of your body.
For use of CBRS bands, the CBSD Category of the final Host equipment will be dependent on the power settings and antenna gain used.

Innovation, Science and Economic Development Canada

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's license-exempt RSS(s). Operation is subject to the following two conditions:

...

Hereby, Mikrotīkls SIA declares that the radio equipment type RBLDFR&R11e-LTE6 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://mikrotik.com/products

...