...
Property | Description |
---|---|
port (interface) | Used bonding port |
key (integer) | Shows the local LACP aggregation key. The lower 6 bits are automatically assigned based on individual port link speed and duplex. The upper 10 bits can be manually specified using the lacp-user-key setting (available only in since RouterOS v7.3). |
flags (string) | Shows the local LACP flags: A - activity (link is active, otherwise passive) |
partner-sys-id (MAC address) | Shows the partner LACP system ID |
partner-sys-priority (integer) | Shows the partner LACP priority |
partner-key (integer) | Shows the partner LACP aggregation key |
partner-flags (string) | Shows the partner LACP flags |
...
Property | Description |
---|---|
arp (disabled | enabled | proxy-arp | reply-only; Default: enabled) | Address Resolution Protocol for the interface.
|
arp-interval (time; Default: 00:00:00.100) | Time in milliseconds defines how often to monitor ARP requests |
arp-ip-targets (IP address; Default: ) | IP target address which will be monitored if link-monitoring is set to arp. You can specify multiple IP addresses, separated by a comma |
comment (string; Default: ) | Short description of the interface |
disabled (yes | no; Default: no) | Changes whether the bonding interface is disabled |
down-delay (time; Default: 00:00:00) | If a link failure has been detected, the bonding interface is disabled for a down-delay time. The value should be a multiple of mii-interval, otherwise, it will be rounded down to the nearest value. This property only has an effect when link-monitoring is set to mii . |
forced-mac-address (MAC address; Default: none) | By default, the bonding interface will use the MAC address of the first selected slave interface. This property allows to configure static MAC address for the bond interface (all zeros, broadcast or multicast addresses will not apply). RouterOS will automatically change the MAC address for slave interfaces and it will be visible in /interface ethernet configuration export |
lacp-rate (1sec | 30secs; Default: 30secs) | Link Aggregation Control Protocol rate specifies how often to exchange with LACPDUs between bonding peers. Used to determine whether a link is up or other changes have occurred in the network. LACP tries to adapt to these changes providing failover. |
lacp-user-key (integer: 0..1023; Default: 0) | Specifies the upper 10 bits of the port key. The lower 6 bits are automatically assigned based on individual port link speed and duplex. The setting is available only in since RouterOS v7.3. |
link-monitoring (arp | mii | none; Default: mii) | Method to use for monitoring the link (whether it is up or down)
|
min-links (integer: 0..4294967295; Default: 0) | How many active slave links needed for bonding to become active |
mii-interval (time; Default: 00:00:00.100) | How often to monitor the link for failures (the parameter used only if link-monitoring is mii) |
mlag-id (integer: 0..4294967295; Default:) | Changes MLAG ID for bonding interface. The same MLAG ID should be used on both peer devices to successfully create a single MLAG. See more details on MLAG. |
mode (802.3ad | active-backup | balance-alb | balance-rr | balance-tlb | balance-xor | broadcast; Default: balance-rr) | Specifies one of the bonding policies
|
mtu (integer; Default: 1500) | Maximum Transmit Unit in bytes. Must be smaller or equal to the smallest L2MTU value of a bonding slave. L2MTU of a bonding interface is determined by the lowest L2MTU value among its slave interfaces |
name (string; Default: ) | Name of the bonding interface |
primary (string; Default: none) | Controls the primary interface between active slave ports, works only for active-backup, balance-tlb and balance-alb modes. For active-backup mode, it controls which running interface is supposed to send and receive the traffic. For balance-tlb mode, it controls which running interface is supposed to receive all the traffic, but for balance-alb mode, it controls which interface is supposed to receive the unbalanced traffic (the non-IPv4 traffic). When none of the interfaces are selected as primary, device will automatically select the interface that is configured as the first one. |
slaves (string; Default: none) | At least two ethernet-like interfaces separated by a comma, which will be used for bonding |
up-delay (time; Default: 00:00:00) | If a link has been brought up, the bonding interface is disabled for up-delay time and after this time it is enabled. The value should be a multiple of mii-interval, otherwise, it will be rounded down to the nearest value. This property only has an effect when link-monitoring is set to mii . |
transmit-hash-policy (layer-2 | layer-2-and-3 | layer-3-and-4; Default: layer-2) | Selects the transmit hash policy to use for slave selection in balance-xor and 802.3ad modes
|
...