Page 7 of 51. Showing 508 results (0.013 seconds)
PtP CLI example
" mtu=auto actual-mtu=1500 l2mtu=65535 arp=enabled arp-timeout=auto mac-address=1A:7F:BB:41:B0:94 protocol-mode=rstp fast-forward=yes igmp-snooping=no auto-mac=yes ageing-time=5m priority=0x8000 max-message-age=20s forward-delay=15s transmit-hold-count=6 vlan-filtering=no dhcp-snooping=no Add interfaceL2TP
be done through a RADIUS client or locally. L2TP traffic uses UDP protocol for both control and data packets. UDP port 1701 is used only for link establishment, further traffic is using any available UDP port (which may or may not be 1701). This means that L2TP can be used with most firewalls and routers (even with NATFail-over PtMP CLI example
actual-mtu=1500 l2mtu=65535 arp=enabled arp-timeout=auto mac-address=1A:7F:BB:41:B0:94 protocol-mode=rstp fast-forward=yes igmp-snooping=no auto-mac=yes ageing-time=5m priority=0x8000 max-message-age=20s forward-delay=15s transmit-hold-count=6 vlan-filtering=no dhcp-snooping=no Set up 60Ghz wirelessSOCKS
of simultaneous connections port (integer: 1..65535; default: 1080) TCP port on which the SOCKS server listens for connections Access List /ip socks access … action (allow | deny; default: allow) allow - allow packets, matching this rule, to be forwarded for further processing deny - deny access for packets, matchingVLAN
, the guide shows how to set up a very basic VLAN trunk/access port configuration. There are some other ways to set up VLAN tagging or VLAN switching … so it uses only the Ethernet header to forward and does not check the IP header. For this reason, we must use the router that is working as a gateway for eachVLANs on Wireless
vlan section with correct vlan-ids [admin@R2] > /interface bridge add fast-forward=no name=bridge1 vlan-filtering=yes /interface bridge port add bridge=bridge1 … and VLAN tag modifications within the bridge. R1: Add necessary VLAN interfaces on ethernet interface to make it a VLAN trunk port. Add ip addresses on VLANCommand Line Interface
The console is used for accessing the MikroTik Router's configuration and management features using text terminals, either remotely using a serial port, telnet … transmitted, 0 packets received, 100% packet loss [admin@MikroTik] /ip/firewall/nat> .. service-port print Flags: X - disabled, I - invalid # NAMEConsole
port, telnet, SSH, or console screen within Winbox, or directly using a monitor and keyboard. The console is also used for writing scripts. This manual describes … firewall nat> .. service-port print Flags: X - disabled, I - invalid # NAME PORTS 0 ftp 21 1 tftp 69 2 irc 6667 3 h323 4 sip 5 pptp [admin@MikroTik] ipLAC and LNS setup with Cisco as LAC
and private networks. Dial-up client uses PPPOE to connect to a L2TP access concentrator (LAC), LAC determines that session should be forwarded through a IP network to the L2TP Network Server (LNS), creates L2TP tunnel and forwards PPP frames to the server where client is authenticated and session established (seeCAPsMAN
to connect to any CAP under CAPsMAN control. When a client attempts to connect to a CAP that is controlled by CAPsMAN, CAP forwards that request to CAPsMAN. As a part … be automatically added as port. Required only when local-forwarding is not used. datapath.bridge-cost (integer [1..200000000]; Default: ) bridge port cost