The device-mode is a feature , which sets specific limitations on a device, or limits access to specific configuration options.
There are two available modes: enterprise and home. By default, all devices use the mode enterprise, which allows all funtionality. functionality except container. The home mode disables the following features: scheduler, socks, fetch, bandwidth-test, traffic-gen, sniffer, romon, proxy, hotspot, email, zerotier, container.
[admin@MikroTik] > system/device-mode/print mode: enterprise
The device mode can be changed by the user, but remote access to the device is not enough to change it. After changing the device-mode, you need to confirm it, by pressing a button on the device itself, or perform a "cold reboot" - that is, unplug the power:.
[admin@MikroTik] > system/device-mode/update mode=home update: please activate by turning power off or pressing reset or mode button in 5m00s -- [Q quit|D dump|C-z pause]
If no power off or button press is performed within the specified time, the mode change is canceled. If another update command is run in parallel, both will be canceled.
It is possible that in the future there will be a number of devices that will be set to mode home at the factory, which means that they will reach users with limited functionality, and then if you want advanced features, you will have to change it to enterprise manually.
The following properties
The following commands are available in the system/device-mode/ menu.:
Returns value that you can assign to variable or print on the screen.
|Shows the active mode and its properties.|
|update||Updates selected properties.|
|Applies changes to the specified properties, see below.|
|container, fetch, scheduler, traffic-gen, |
ipsec, pptp, smb, l2tp, proxy, sniffer, zerotier, bandwidth-test, email, hotspot, romon, socks. (yes | no; Default: yes, for enterprise mode)
|The list of available features, which can be controlled with the device-mode option.|
|activation-timeout (default: 5m);||The reset button or power off activation timer timeout can be set in range 00:00:10 .. 1d00:00:00. If the reset button is not pressed (or cold reboot is not performed) during this interval, the update will be canceled.|
|flagging-enabled (yes | no; Default: yes)||Enable or disable the flagged status. See below for a detailed description.|
|flagged (yes | no; Default: no)||RouterOS employs various mechanisms to detect tampering with it's system files. If the system has detected unauthorized access to RouterOS, the status "flagged" is set to yes. If "flagged" is set to yes, for your safety, certain limitations are put in place. See below chapter for more information.|
|mode: (home, enterprise; default: enterprise);||Allows choosing from available modes that will limit device functionality. In the future, various modes could be added. |
By default, enterprise mode allows all options except container. So to use the container feature, you will need to turn it on by performing a device-mode update.
By default, home mode disables the following features: scheduler, socks, fetch, bandwidth-test, traffic-gen, sniffer, romon, proxy, hotspot, email, zerotier, container.
More specific control over the available features is possible. Each of the features controlled by device-mode can be specifically turned on or off, for example:
If the update command specifies any of the modeparameters, this update replaces the entire device-mode configuration. In this case, all "per-feature" settings will be lost, except those specified with this command. For instance:
[admin@MikroTik] > system/device-mode/update hotspot=no -- reboot -- [admin@MikroTik] > system/device-mode/print mode: enterprise sniffer: no hotspot: no
If the feature is disabled, an error message is displayed for interactive commands:
However, it is possible to add the configuration to a disabled feature, but there will be a comment showing the disabled feature in the device-mode:
[admin@MikroTik] > ip hotspot/add interface=ether1 [admin@MikroTik] > ip hotspot/print Flags: X, S - HTTPS Columns: NAME, INTERFACE, PROFILE, IDLE-TIMEOUT # NAME INTERFACE PROFILE IDLE-TIMEOUT ;;; inactivated, not allowed by device-mode 0 X hotspot1 ether1 default 5m
Along with thedevice-mode feature, RouterOS now can analyse the whole configuration at system startup, to determine if there are any signs of unauthorized access to your router. If suspicious configuration is detected, the suspicious configuration will be disabled and the flagged parameter will be set to "yes":. The device has now a Flagged state and enforces certain limitations.
[admin@MikroTik] > system/device-mode/print mode: enterprise flagged: yes sniffer: no hotspot: no
If the system has this flagged status, the current configuration works, but it is not possible to perform a series of the following actions:
bandwidth-test, traffic-generator, sniffer, as well as configuration actions that enable or create new configuration entries (it will still be possible to disable or delete them) for the following programs: system scheduler, SOCKS proxy, pptp, l2tp, ipsec, proxy, smb.
When performing the aforementioned actions while the router is "has the flagged "state, you will receive an error message:
[admin@MikroTik] > /tool sniffer/quick failure: configuration flagged, check all router configuration for unauthorized changes and update device-mode [admin@MikroTik] > /int l2tp-client/add connect-to=18.104.22.168 user=user failure: configuration flagged, check all router configuration for unauthorized changes and update device-mode
To remove exit the flagged noticestate, you must perform the command "/system/device-mode/update flagged=no". The system will ask to either press a button, or issue a hard reboot (cut power physically or do a hard reboot of the virtual machine).
Important! Although the system has disabled any malicious looking rules, which triggered the flagged state, it is crucial to inspect all of your configuration for other unknown things, before exiting the flagged state. If your system has been flagged, assume that your system has been compromised and do a full audit of all settings before re-enabling the system for use. After completing the audit, change all the system passwords and upgrade to the latest RouterOS version.