...
IGMP (Internet Group Management Protocol) and MLD (Multicast Listener Discovery) snooping allow the bridge to listen to IGMP/MLD communication and make forwarding decisions for multicast traffic based on the received information. By default, bridges are flooding multicast traffic to all bridge ports just like broadcast traffic, which might not always be the best scenario (e.g. for multicast video traffic or SDVoE applications). The IGMP/MLD snooping tries to solve the problem by forwarding the multicast traffic only to ports where clients are subscribed to, see an IGMP/MLD network concept below. RouterOS bridge is able to process IGMP v1/v2/v3 and MLD v1/v2 packets. . The implemented bridge IGMP/MLD snooping is based on RFC4541, and IGMP/MLD protocols are specified on RFC1112 (IGMPv1) RFC2236 (IGMPv2), RFC3376 (IGMPv3), RFC2710 (MLDv1), RFC3810 (MLDv2).
| Note |
|---|
Source-specific multicast forwarding is not supported for IGMP v3 and MLD v2. |
Configuration options
The bridge will process This section describes the IGMP and /MLD snooping bridge configuration options.
Sub-menu: /interface bridge
messages only when igmp-snooping is enabled. Additionally, the bridge should have an active IPv6 address in order to process MLD packets. At first, the bridge does not restrict the multicast traffic and all multicast packets get flooded. Once IGMP/MLD querier is detected by receiving an IGMP/MLD query message (the query message can be received by an external multicast router or locally by bridge interface with enabled multicast-querier), only then the bridge will start to restrict unknown IP multicast traffic and forward the known multicast from the multicast database (MDB). The IGMP and MLD querier detection is independent, which means that detecting only IGMP querier will not affect IPv6 multicast forwarding and vice versa. The querier detection also does not restrict the forwarding of non-IP and link-local multicast groups, like 224.0.0.0/24 and ff02::1.
| Warning |
|---|
CRS3xx series devices with Marvell-98DX3236, Marvell-98DX224S or Marvell-98DX226S switch chip are not able to distinguish non-IP/IPv4/IPv6 multicast packets once IGMP or MLD querier is detected. It means that the switch will stop forwarding all unknown non-IP/IPv4/IPv6 multicast traffic when the querier is detected. This does not apply to certain link-local multicast address ranges, like 224.0.0.0/24 or ff02::1. |
Configuration options
...
This section describes the IGMP and MLD snooping bridge configuration options.
Sub-menu: /interface bridge
Property | Description |
|---|---|
| igmp-snooping (yes | no; Default: no) | Enables IGMP and MLD snooping. |
| igmp-version (2 | 3; Default: 2) | Selects the IGMP version in which IGMP membership queries will be generated when the bridge interface is acting as an IGMP querier |
Property
Description
igmp-snooping and multicast-querier is set to yes.When the last client on the bridge port unsubscribes to a multicast group and the bridge is acting as an active querier, the bridge will send group-specific IGMP/MLD query, to make sure that no other client is still subscribed. The setting changes the response time for these queries. In case no membership reports are received in a certain time period (last-member-interval * last-member-query-count), the multicast group is removed from the multicast database (MDB).
If the bridge port is configured with fast-leave, the multicast group is removed right away without sending any queries.
This property only has an effect when igmp-snooping and multicast-querier is set to yes.
last-member-interval pass until the IGMP/MLD snooping bridge stops forwarding a certain multicast stream. This property only has an effect when igmp-snooping and multicast-querier is set to yes.| . This property only has an effect when |
igmp-snooping |
and multicast-querier is set to yes. |
| last-member- |
| interval ( |
| time; Default: |
| 1s) |
Multicast querier generates periodic IGMP/MLD general membership queries to which all IGMP/MLD capable devices respond with an IGMP/MLD membership report, usually a PIM (multicast) router or IGMP proxy generates these queries.
By using this property you can make an IGMP/MLD snooping enabled bridge to generate IGMP/MLD general membership queries. This property should be used whenever there is no active querier (PIM router or IGMP proxy) in a Layer2 network. Without a multicast querier in a Layer2 network, the Multicast Database (MDB) is not being updated, the learned entries will timeout and IGMP/MLD snooping will not function properly.
Only untagged IGMP/MLD general membership queries are generated, IGMP queries are sent with IPv4 0.0.0.0 source address, MLD queries are sent with IPv6 link-local address of the bridge interface. The bridge will not send queries if an external IGMP/MLD querier is detected (see the monitoring values igmp-querier and mld-querier).
igmp-snoopingWhen the last client on the bridge port unsubscribes to a multicast group and the bridge is acting as an |
igmp-snooping and multicast-querier is set to yes.active querier, the bridge will send group-specific IGMP/MLD query, to make sure that no other client is still subscribed. The setting changes the response time for these queries. In case no membership reports are received in a certain time period ( If the bridge port is configured with fast-leave, the multicast group is removed right away without sending any queries. This property only has an effect when | |
| last-member-query-count (integer: 0..4294967295; Default: 2) | How many times should last-member-interval pass until the IGMP/MLD snooping bridge stops forwarding a certain multicast stream. This property only has an effect when igmp-snooping and multicast-querier is set to yes. |
| membership-interval (time; Default: 4m20s) | The amount of time after an entry in the Multicast Database (MDB) is removed if no IGMP/MLD membership reports are received on a bridge port. This property only has an effect when igmp-snooping is set to yes. |
| mld-version (1 | 2; Default: 1) | Selects the MLD version in which MLD membership queries will be generated, when the bridge interface is acting as an MLD querier. This property only has an effect when the bridge has an active IPv6 address, igmp-snooping and multicast-querier |
is set to yes. |
| multicast- |
| querier ( |
| yes | no; Default: |
| no) |
Multicast querier generates periodic IGMP/MLD |
igmp-snooping is set to yes.disabled- disabled multicast router state on the bridge interface. Unregistered multicast and IGMP/MLD membership reports are not sent to the bridge interface regardless of what is configured on the bridge interface.permanent- enabled multicast router state on the bridge interface. Unregistered multicast and IGMP/MLD membership reports are sent to the bridge interface itself regardless of what is configured on the bridge interface.temporary-query- automatically detect multicast router state on the bridge interface using IGMP/MLD queries.
general membership queries to which all IGMP/MLD capable devices respond with an IGMP/MLD membership report, usually a PIM (multicast) router or IGMP proxy generates these queries. By using this property you can make an IGMP/MLD snooping enabled bridge to generate IGMP/MLD general membership queries. This property should be used whenever there is no active querier (PIM router or IGMP proxy) in a Layer2 network. Without a multicast querier in a Layer2 network, the Multicast Database (MDB) is not being updated, the learned entries will timeout and IGMP/MLD snooping will not function properly. Only untagged IGMP/MLD general membership queries are generated, IGMP queries are sent with IPv4 0.0.0.0 source address, MLD queries are sent with IPv6 link-local address of the bridge interface. The bridge will not send queries if an external IGMP/MLD querier is detected (see the monitoring values |
This property only has an effect when |
| multicast- |
| router ( |
| disabled | permanent | temporary-query; Default: |
igmp-snooping and multicast-querier is set to yes.| temporary-query) | A multicast router port is a port where a multicast router or querier is connected. On this port, unregistered multicast streams and IGMP/MLD membership reports will be sent. This setting changes the state of the multicast router for a bridge interface itself. This property can be used to send IGMP/MLD membership reports and multicast traffic to the bridge interface for further multicast routing or proxying. This property only has an effect when igmp-snooping |
multicast-querier is set to is set to yes. |
igmp-snooping and multicast-querier is set to yes.
|
| querier-interval (time; Default: |
| 4m15s) |
Changes the timeout period for detected querier and multicast-router ports. This property only has an effect when igmp-snooping |
multicast-querier is set to yes. |
Sub-menu: /interface bridge port
| query-interval (time; Default: 2m5s) | Changes the interval on how often IGMP/MLD general membership queries are sent out when the bridge interface is acting as an IGMP/MLD querier. The interval takes place when the last startup query is sent. This property only |
Property
Description
has an effect when igmp-snooping and multicast-querier is set to yes. |
| query-response- |
| interval ( |
| time; Default: |
| 10s) | The setting changes the response time for general IGMP/MLD queries when the bridge is acting as an IGMP/MLD querier. This property only has an effect when igmp-snooping and multicast-querier is set to yes. |
disabled - disabled multicast router state on the bridge port. Unregistered multicast and IGMP/MLD membership reports are not sent to the bridge port regardless of what is connected to it.permanent - enabled multicast router state on the bridge port. Unregistered multicast and IGMP/MLD membership reports are sent to the bridge port regardless of what is connected to it.temporary-query - automatically detect multicast router state on the bridge port using IGMP/MLD queries.Monitoring and troubleshooting
This section describes the IGMP/MLD snooping bridge monitoring and troubleshooting options.
...
| startup-query-count (integer: 0..4294967295; Default: 2) | Specifies how many times general IGMP/MLD queries must be sent when bridge interface is enabled or active querier timeouts. This property only has an effect when igmp-snooping and multicast-querier is set to yes. |
| startup-query-interval (time; Default: 31s250ms) | Specifies the interval between startup general IGMP/MLD queries. This property only has an effect when igmp-snooping and multicast-querier is set to yes. |
Sub-menu: /interface bridge
...
port
Property | Description |
|---|
| fast-leave ( |
vlan-filtering is enabled.| yes | no; Default: no) | Enables IGMP/MLD fast leave feature on the bridge port. The bridge will stop forwarding multicast traffic to a bridge port when an IGMP/MLD leave message is received. This property only has an effect when igmp-snooping is set to yes. |
| multicast-router (disabled | permanent | temporary-query; Default: temporary-query) | A multicast router port is a port where a multicast router or querier is connected. On this port, unregistered multicast streams and IGMP/MLD membership reports will be sent. This setting changes the state of the multicast router for bridge ports. This property can be used to send IGMP/MLD membership reports and multicast streams to certain bridge ports for further multicast routing or proxying. This property only has an effect when igmp-snooping is set to yes.
|
| unknown-multicast-flood (yes | no; Default: yes) | Changes the multicast flood option on bridge port, only controls the egress traffic. When enabled, the bridge allows flooding multicast packets to the specified bridge port, but when disabled, the bridge restricts multicast traffic from being flooded to the specified bridge port. The setting affects all multicast traffic, this includes non-IP, IPv4, IPv6 and the link-local multicast ranges (e.g. 224.0.0.0/24 and ff02::1). Note that when When using this setting together with |
Monitoring and troubleshooting
...
This section describes the IGMP/MLD snooping bridge monitoring and troubleshooting options.
To monitor learned multicast database (MDB) entries, use the print command.
Sub-menu: /interface bridge mdb
Property | Description |
|---|---|
| bridge (read-only: name) | Shows the bridge interface the entry belongs to. |
| group (read-only: ipv4 | ipv6 address) | Shows a multicast group address. |
| ports (read-only: name) | Shows the bridge ports which are subscribed to the certain multicast group. |
| vid (read-only: integer) | Shows the VLAN ID for the multicast group, only applies when vlan-filtering is enabled. |
| Code Block | ||
|---|---|---|
| ||
[admin@MikroTik] /interface bridge mdb print
GROUP | ||
| Code Block | ||
| ||
[admin@MikroTik] /interface bridge mdb print GROUP VID PORTS BRIDGE 229.1.1.2 10 ether3 bridge1 229.2.2.2 10 ether3 bridge1 ff1e::2010 VID PORTS 10BRIDGE ether3 bridge1 ff1e::2011 229.1.1.2 1010 ether3 bridge1 |
To monitor the current status of a bridge interface, use the monitor command.
Sub-menu: /interface bridge
...
Property
...
Description
...
| Code Block | ||
|---|---|---|
| ||
[admin@MikroTik] /interface bridge monitor bridge1 bridge1 229.2.2.2 state: enabled 10 ether3 bridge1 ff1e::2010 current-mac-address: 64:D1:54:C7:3A:59 root-bridge: yes root-bridge-id: 0x8000.64:D1:54:C7:3A:59 root-path-cost: 0 10 ether3 bridge1 root-port: none ff1e::2011 port-count: 3 designated-port-count: 3 fast-forward: no multicast-router: no 10 ether3 igmp-querier: ether2 192.168.10.10 mld-querier: ether2 fe80::e68d:8cff:fe39:3824 bridge1 |
To monitor the current status of a bridge portsinterface, use the monitor command.
Sub-menu: /interface bridge
...
Property | Description |
|---|
| igmp- |
| querier ( |
| none | interface & IPv4 address) | Shows |
a bridge port and source IP address from the detected IGMP querier. Only shows detected external IGMP querier, local bridge IGMP querier (including IGMP proxy and PIM) will not be displayed. Monitoring value appears only when igmp-snooping is enabled. | |
| mld-querier (none | interface & IPv6 address) | Shows a bridge port and source IPv6 address from the detected MLD querier. Only shows detected external MLD querier, local bridge MLD querier will not be displayed. Monitoring value appears only when igmp-snooping is enabled and the bridge has an active IPv6 address. |
| multicast-router (yes | no) | Shows if a multicast router is detected on the bridge interface. Monitoring value appears only when igmp-snooping is enabled. |
| Code Block | ||
|---|---|---|
| ||
[admin@MikroTik] /interface bridge monitor bridge1
| ||
| Code Block | ||
[admin@MikroTik] > /interface bridge port monitor [find] interface: ether2 ether3 ether4 statusstate: in-bridge enabled in-bridge in-bridgecurrent-mac-address: 64:D1:54:C7:3A:59 portroot-numberbridge: 1 yes 2 root-bridge-id: 0x8000.64:D1:54:C7:3A:59 root-path-cost: 0 3 root-port: none role: port-count: 3 designated-port designated-port designated-port edge-port: no yes yes edge-port-discovery: yes yes yes point-to-point-port: yes yes yes external-fdb: no no no sending-rstp: yes yes yes learning: yes yes yes forwarding: yes yes yes multicast-router: yes no no hw-offload-group: switch1 switch1 switch1 |
...
-count: 3
fast-forward: no
multicast-router: no
igmp-querier: ether2 192.168.10.10
mld-querier: ether2 fe80::e68d:8cff:fe39:3824 |
To monitor the current status of bridge ports, use the monitor command.
Sub-menu: /interface bridge port
Property | Description |
|---|---|
| multicast-router (yes | no) | Shows if a multicast router is detected on the port. Monitoring value appears only when igmp-snooping is enabled. |
| Code Block | ||
|---|---|---|
| ||
[admin@MikroTik] > /interface bridge port monitor [find]
interface: ether2 ether3 ether4
status: in-bridge in-bridge in-bridge
port-number: 1 2 3
role: designated-port designated-port designated-port
edge-port: no yes yes
edge-port-discovery: yes yes yes
point-to-point-port: yes yes yes
external-fdb: no no no
sending-rstp: yes yes yes
learning: yes yes yes
forwarding: yes yes yes
multicast-router: yes no no
hw-offload-group: switch1 switch1 switch1 |
Configuration examples
...
Below are described the most common configuration examples. Some examples are using a bridge with VLAN filtering, so make sure to understand the filtering principles first - bridge VLAN filtering, bridge VLAN table.
Basic IGMP snooping configuration
The first example consists only of a single IGMP snooping bridge, a single multicast source device, and a couple of multicast client devices. See a network scheme below.
First, create a bridge interface with enabled IGMP snooping. In this example, there is no active IGMP querier (no multicast router or proxy), so a local IGMP querier must be enabled on the same bridge. This can be done with a multicast-querier setting. If there is no active IGMP querier in the LAN, the unregistered IP multicast will be flooded and multicast entries will always timeout from the multicast database.
| Code Block | ||
|---|---|---|
| ||
/interface bridge
add igmp-snooping=yes multicast-querier=yes name=bridge1 |
Then add necessary interfaces as bridge ports.
| Code Block | ||
|---|---|---|
| ||
/interface bridge port
add bridge=bridge1 interface=ether2
add bridge=bridge1 interface=ether3
add bridge=bridge1 interface=ether4
add bridge=bridge1 interface=ether5 |
The basic IGMP snooping configuration is finished. Use "/interface bridge mdb print" command to monitor the active multicast groups. If necessary, you can configure an IP address and DHCP server on the same bridge interface.
IGMP snooping configuration with VLANs
The second example adds some complexity. There are two IGMP snooping bridges and we need to isolate the multicast traffic on a different VLAN. See a network scheme below.
First, create a bridge on both devices and add needed interfaces as bridge ports. To change untagged VLAN for a bridge port, use the pvid setting. The Bridge1 will be acting as an IGMP querier. Below are configuration commands for the Bridge1:
| Code Block | ||
|---|---|---|
| ||
/interface bridge
add igmp-snooping=yes multicast-querier=yes name=bridge1
/interface bridge port
add bridge=bridge1 interface=ether2 pvid=10
add bridge=bridge1 interface=ether3 pvid=10
add bridge=bridge1 interface=ether4 pvid=10
add bridge=bridge1 interface=ether5 pvid=20
add bridge=bridge1 interface=sfp-sfpplus1 pvid=10 |
And for the Bridge2:
| Code Block | ||
|---|---|---|
| ||
/interface bridge
add igmp-snooping=yes name=bridge1
/interface bridge port
add bridge=bridge1 interface=ether3 pvid=10
add bridge=bridge1 interface=ether4 pvid=10
add bridge=bridge1 interface=ether5 pvid=20
add bridge=bridge1 interface=sfp-sfpplus1 pvid=10 |
| Note |
|---|
Bridge IGMP querier implementation can only send untagged IGMP queries. In case tagged IGMP queries should be sent or IGMP queries should be generated in multiple VLANs, it is possible to install a multicast package, add a VLAN interface and configure a PIM interface on VLAN. The PIM interface can be used as an IGMP querier. |
Make sure to configure management access for devices. It is essential when configuring a bridge with VLAN filtering. In this example, a VLAN 99 interface with an IP address is added to the bridge. This VLAN will be allowed on the tagged sfp-sfpplus1 port. Below are configuration commands for the Bridge1:
| Code Block | ||
|---|---|---|
| ||
/interface vlan
add interface=bridge1 name=MGMT vlan-id=99
/ip address
add address=192.168.99.1/24 interface=MGMT network=192.168.99.0
/interface bridge vlan
add bridge=bridge1 tagged=bridge1,sfp-sfpplus1 vlan-ids=99 |
And for the Bridge2:
| Code Block | ||
|---|---|---|
| ||
/interface vlan
add interface=bridge1 name=MGMT vlan-id=99
/ip address
add address=192.168.99.2/24 interface=MGMT network=192.168.99.0
/interface bridge vlan
add bridge=bridge1 tagged=bridge1,sfp-sfpplus1 vlan-ids=99 |
Add bridge VLAN entries and specify tagged and untagged ports. The VLAN 99 entry was already created when configuring management access, only VLAN 10 and VLAN 20 should be added now. Below are configuration commands for the Bridge1:
| Code Block | ||
|---|---|---|
| ||
/interface bridge vlan
add bridge=bridge1 untagged=ether2,ether3,ether4,sfp-sfpplus1 vlan-ids=10
add bridge=bridge1 tagged=sfp-sfpplus1 untagged=ether5 vlan-ids=20 |
And for the Bridge2:
| Code Block | ||
|---|---|---|
| ||
/interface bridge vlan
add bridge=bridge1 untagged=ether3,ether4,sfp-sfpplus1 vlan-ids=10
add bridge=bridge1 tagged=sfp-sfpplus1 untagged=ether5 vlan-ids=20 |
Last, enable VLAN filtering. Below is the configuration command for Bridge1 and Bridge2:
| Code Block | ||
|---|---|---|
| ||
/interface bridge set [find name=bridge1] vlan-filtering=yes |
At this point, VLANs and IGMP snooping are configured and devices should be able to communicate through ports. However, it is recommended to go even a step further and apply some additional filtering options. Enable ingress-filtering and frame-types on bridge ports. Below are configuration commands for the Bridge1:
| Code Block | ||
|---|---|---|
| ||
/interface bridge port
set [find interface=ether2] ingress-filtering=yes frame-types=admit-only-untagged-and-priority-tagged
set [find interface=ether3] ingress-filtering=yes frame-types=admit-only-untagged-and-priority-tagged
set [find interface=ether4] ingress-filtering=yes frame-types=admit-only-untagged-and-priority-tagged
set [find interface=ether5] ingress-filtering=yes frame-types=admit-only-untagged-and-priority-tagged
set [find interface=sfp-sfpplus1] ingress-filtering=yes |
And for the Bridge2:
| Code Block | ||
|---|---|---|
| ||
/interface bridge port
set [find interface=ether3] ingress-filtering=yes frame-types=admit-only-untagged-and-priority-tagged
set [find interface=ether4] ingress-filtering=yes frame-types=admit-only-untagged-and-priority-tagged
set [find interface=ether5] ingress-filtering=yes frame-types=admit-only-untagged-and-priority-tagged
set [find interface=sfp-sfpplus1] ingress-filtering=yes |