...
| Property | Description | ||||||
|---|---|---|---|---|---|---|---|
| arp (disabled | enabled | local-proxy-arp | proxy-arp | reply-only) | Address Resolution Protocol mode:
| ||||||
| arp-timeout (time interval | 'auto') | Determines how long a dynamically added ARP table entry is considered valid since the last packet was received from the respective IP address. Value auto equals to the value ofarp-timeout in/ip settings, which defaults to 30s. | ||||||
channel.band (2ghz-g | 2ghz-n | 2ghz-ax | 5ghz-a | 5ghz-ac | 5ghz-an | 5ghz-ax) | Supported frequency band and wireless standard. Defaults to newest supported standard. | ||||||
| channel.frequency (list of integers or integer ranges) |
For an interface in station mode, determines frequencies on which to scan for APs. Leave unset (default) to consider all frequencies supported by the radio and permitted by the applicable regulatory profille. The parameter can contain 1 or more comma-separated values of integers or, optionally, ranges of integers denoted using the syntax RangeBeginning-RangeEnd:RangeStep Examples of valid channel.frequency values:
| ||||||
| channel.secondary-frequency (list of integers | 'disabled') | Frequency (in MHz) to use for the center of the secondary part of a split 80+80MHz channel. Only official 80MHz channels (5210, 5290, 5530, 5610, 5690, 5775) are supported. Leave unset (default) for automatic selection of secondary channel frequency. | ||||||
| channel.skip-dfs-channels (10min-cac | all | disabled) | Whether to avoid using channels, on which channel availability check (listening for presence of radar signals) is required.
| ||||||
channel.width ( 20mhz | 20/40mhz | 20/40mhz-Ce | 20/40mhz-eC | 20/40/80mhz | 20/40/80+80mhz | 20/40/80/160mhz) | Width of radio channel. Defaults to widest channel supported by the radio hardware. | ||||||
configuration.chains (list of integer 0..7 ) | Radio chains to use for receiving signals. Defaults to all chains available to the corresponding radio hardware. | ||||||
configuration.country (name of a country) | Determines, which regulatory domain restrictions are applied to an interface. Defaults to "United States". Note: It is important to set this value correctly to comply with local regulations and ensure interoperability with other devices. | ||||||
configuration.hide-ssid (no | yes) |
Default: no | ||||||
| configuration.mode (ap | station) | Interface operation mode
| ||||||
| configuration.ssid (string) | The name of the wireless network, aka the (E)SSID. No default value. | ||||||
| configuration.tx-chains (list of integer 0..7) | Radio chains to use for transmitting signals. Defaults to all chains available to the corresponding radio hardware. | ||||||
| configuration.tx-power (integer 0..40) | A limit on the transmit power (in dBm) of the interface. Can not be used to set power above limits imposed by the regulatory profile. Unset by default. | ||||||
| disable-running-check (no | yes) |
| ||||||
disabled (no | yes) (X) | Hardware interfaces are disabled by default. Virtual interfaces are not. | ||||||
mac-address (MAC) | MAC address (BSSID) to use for an interface. Hardware interfaces default to the MAC address of the associated radio interface. Default MAC addresses for virtual interfaces are generated by
| ||||||
master-interface (interface) | Multiple interface configurations can be run simultaneously on every wireless radio. Only one of them determines the radio's state (whether it is enabled, what frequency it's using, etc). This 'master' interface, is bound to a radio with the corresponding radio-mac. To create additional ('virtual') interface configurations on a radio, they need to be bound to the corresponding master interface. No default value. | ||||||
name (string) | A name for the interface. Defaults to wifiN, where N is the lowest integer that has not yet been used for naming an interface. | ||||||
security.authentication-types (list of wpa-psk, wpa2-psk, wpa-eap, wpa2-eap, wpa3-psk, owe, wpa3-eap, wpa3-eap-192) | Authentication types to enable on the interface. The default value is an empty list (no authenticaion, an open network). Configuring a passphrase, adds to the default list the wpa2-psk authentication method (if the interface is an AP) or both wpa-psk and wpa2-psk (if the interface is a station). Configuring an eap-username and an eap-password adds to the default list wpa-eap and wpa2-eap authentication methods. | ||||||
| security.dh-groups (list of 19, 20, 21) | Identifiers of elliptic curve cryptography groups to use in SAE (WPA3) authentication. | ||||||
| security.disable-pmkid (no | yes) | Whether to include PMKID into the EAPOL frame sent out by the Access Point. Disabling PMKID can cause compatibility issues with devices that use the PMKID to connect to an Access Point.
| ||||||
| security.eap-accounting (no | yes) | Send accounting information to RADIUS server for EAP-authenticated peers. Default: no. | ||||||
| |||||||
| security.eap-accounting (no | yes) | Explicitly enable accounting packets for RADIUS EAP authentication. Default: no. | security.eap-anonymous-identity (string) | Optional anonymous identity for EAP outer authentication. No default value. | ||||
| security.eap-certificate-mode (dont-verify-certificate | no-certificates | verify-certificate | verify-certificate-with-crl) | Policy for handling the TLS certificate of the RADIUS server.
| ||||||
| security.eap-methods (list of peap, tls, ttls) | EAP methods to consider for authentication. Defaults to all supported methods. | ||||||
| security.eap-password (string) | Password to use, when the chosen EAP method requires one. No default value. | ||||||
| security.eap-tls-certificate (certificate) | Name or id of a certificate in the device's certificate store to use, when the chosen EAP authentication method requires one. No default value. | ||||||
| security.eap-username (string) | Username to use when the chosen EAP method requires one. No default value. | ||||||
| security.encryption (list of ccmp, ccmp-256, gcmp, gcmp-256, tkip) | A list of ciphers to support for encrypting unicast traffic. Defaults to ccmp. | ||||||
| security.group-encryption(ccmp | ccmp-256 | gcmp | gcmp-256 | tkip) | Cipher to use for encrypting multicast traffic. Defaults to ccmp. | ||||||
| security.group-key-update (time interval 30s..1h) | Interval at which the group temporal key (key for encrypting broadcast traffic) is renewed. Defaults to 5 minutes. | ||||||
| security.management-encryption (cmac | cmac-256 | gmac | gmac-256) | Cipher to use for encrypting protected management frames. Defaults to cmac. | ||||||
security.management-protection (allowed | disabled | required) | Whether to use 802.11w management frame protection. Incompatible with management frame protection in standard wireless package. Default value depends on value of selected authentication type (WPA (1) does not support MFP, while WPA3 requires it). | ||||||
security.owe-transition-interface (interface) | Name or internal id of an interface whose MAC address and SSID to advertise as the matching AP when running in OWE transition mode. Required for setting up open APs that offer OWE, but also work with older devices that don't support the standard. See configuration example below. | ||||||
| security.passphrase (string of up to 63 characters) | Passphrase to use for PSK authentication types. Defaults to an empty string - "". WPA-PSK and WPA2-PSK authentication requires a minimum of 8 chars, while WPA3-PSK does not have minimum passphrase length. | ||||||
| security.sae-anti-clogging-threshold ('disabled' | integer) | Due to SAE (WPA3) associations being CPU resource intensive, overwhelming an AP with bogus authentication requests makes for a feasible denial-of-service attack. This parameter provides a way to mitigate such attacks by specifying a threshold of in-progress SAE authentications, at which the AP will start requesting that client devices include a cookie bound to their MAC address in their authentication requests. It will then only process authentication requests which contain valid cookies. Default: disabled. | ||||||
| security.sae-max-failure-rate ('disabled' | integer) | Rate of failed SAE (WPA3) associations per minute, at which the AP will stop processing new association requests. Defaults to disabled. | ||||||
| security.wps (disabled | push-button) |
| ||||||
...