...
This article describes supported add-on peripherals for RouterBOARD hardware devices.
Model | Tested RouterOS version | Comments | Format | Passthrough support | Technologies |
---|
BandRich C501 | v5.25 and v6.0 | USB | ? | LTE | Sierra Wireless MC7710/MC7700/MC7750 | v5.25, v6.0 and 6.40RC43 | If modem uses firmware 3.5 it should be upgraded to 3.5.23.2 firmware release in order to work in RouterOS correctly again. | MiniPCI-e | N | LTE |
Yota LU150 | v5.22 and v6.4 | Some settings are ignored. Works in Russian markets.Alcatel IK40 | v6.41RC11 | LTE interface, Modem can be configured only through modems configuration WEB page. | USB | N | LTE |
Alcatel IK41 | v6.48 | Config-less LTE interface | USB | N | LTE |
Android usb tethering interface | v6.7 | Some settings are ignored. | USB | ? | LTE |
Yota WLTUBA107.0Some settings are ignored. Works in Russian markets. | USB | ? | LTE | Yota wifi modem | v6.7 | Some settings are ignored. Works in Russian markets. | | ( aka "USB Wireless HSDPA/UMTS 2.1GHz GSM/GPRS/EGPRS 900/17000MHz/CDMA 1x EVDO Rev.A") | USB |
| 3G |
BandRich C501 | v5.25 and v6.0 |
| USB | ? | LTE |
Vodafone K43057Some settings are ignored. | USB | ? | LTE | Android usb tethering interface | v6.7 | Some settings are ignored. | USB | ? | LTE |
ZTE MF823 | v6.8 | Some settings are ignored. For some devices it's needed to enter in FACTORY mode to change operating state. | USB | ? | LTE |
ZTE MF825A | v6.xx | Some settings are ignored.xx | Works! Data Channel: 2, Info Channel: 3,Modem Init: AT+CFUN=1, vendor-id="0x2001" device-id="0x7d02" Some info from modem: > H/W Ver.: B1, F/W Ver.: 2.0.1eu, revision: +CGMR: MOLY.WR8.W1231.DC.WG.MP.V3, 2013/04/09 02:08 Different HW revisions might not work with RouterOS | USB |
| 3G |
D-link DWM-222 | v6.38 | Multiple modem versions with same marketing name exist, only H/W ver: A1 supported as config-less LTE interface | USB | N |
|
Dell DW5821e | v7.4beta4 and higher | MBIM driver. Revision: T77W968.F1.0.0.5.2.VZ.013 044 | M.2 |
| 3G,LTE |
Dell Wireless 5530 HSPA | v6.1 and higher | Data channel 0, Info channel 0, init: AT+CFUN=1 (needs manualy change profile by command AT*ENAP=1,1) | MiniPCI-e |
| 3G |
Ericsson F5521gw | v6.x and higher |
| MiniPCI-e |
| 3G |
Fibocom FM150-AE | v7.1beta5 | MBIM driver. Revision: 89603.1000.00.01.01.03 | M.2 |
| 3G, LTE, 5G |
Fibocom NL-952-EAU | v7.1beta5 | MBIM driver. Revision: 19600.7000.00.04.01.05 | M.2 |
| 3G, LTE |
Marvell PXA1802 based modems | v7.2.2 | Vendorid=0x1286 deviceid=0x4e31 | mini-PCIe |
|
|
Huawei E153 | v6.31< and higher |
| USB |
| 3G |
Huawei E171 | v6.xx | Works! ppp interface, vendorid=0x12d1 deviceid=0x140c | USB |
| 3G |
Huawei e3131 | v6.xx and higher | ppp interface | USB |
| 3G |
Huawei E3372h, E5576h, E8372h | v6.8 | Config-less LTE interface for modems with vendor-id="0x12d1" device-id="0x14db" Models with suffixes -320 and -608 will not work with RouterOS v6, please use v7 instead. | USB | N | LTE |
Huawei E3276-150 | v6.xx | ppp interface | USB | ? | LTE |
Vodafone K516037Some settings are ignored. | ?LTE | Vodafone K4201-Z | v6.8 | Some settings are ignored. LTE interface. | USB | ? | LTE |
ZTE MF827 | v6.8 | Some settings are ignored. | USB | ? | LTE |
Huawei E3272 | v6.8 | Some settings are ignored. There are multiple versions of this modem. Looks like only modem with device-id="0x14db" works as LTE interface. | Huawei E3531 | v6.24 or 6.40RC25 | There are different versions of this modem E3531-6 works from version 6.40RC25 as ppp, mbim supported only from RouterOS V7 | USB |
| 3G |
Huawei e398 | v6.xx and higher | ppp interface | USB |
| LTE |
Huawei E5377 | v6.36.1 | MIFI unit. No serial support, but works with IP on LTE interface | USB | ? | LTE |
Huawei E5673s-609 | v6.xx | LTE interface | USB | ? | LTE |
Huawei |
E537736.1MIFI unit. No serial support, but works with IP on LTE37 v7.0beta6 | v6 and v7 - config-less LTE interface v7 - by default will try to use modem in MBIM mode | USB | N |
|
Huawei K5161 | v6.47 | Config-less LTE interface | USB |
? | MU609ME909s-120 | v6.28 | Recommended modem firmware version 11 |
MiniPCI-e | ? | 3G | Huawei MU709s-2 | v6.28 | .617.24.00.00 To reduce LTE interface IP subnet mask to /32 configure modem with at-chat command: /interface lte at-chat [find] input="AT^CUSTFEATURE=3,1" | MiniPCI-e | Y |
3GLTE |
Huawei ME909u-521 | v6.11 |
| MiniPCI-e | N | LTE |
Huawei |
ME909s-12028YLTE | SIMcom SIM7100 | v6.xx(ppp) v7.xx (LTE) | Works! PPP interface. And starting with v7.xx it will support LTE interface. vendor-id="0x1e0e" device-id="0x9001"3G |
Huawei MU709s-2 | v6.28 |
| MiniPCI-e |
/ USB w/ converter?Sierra wireless MC73xxLTE | xx(ppp) v7.xx (LTE)Works! PPP interface. And starting with v7.xx it will support LTE interface. MC7304 tested with firmware SWI9X15C_05.05.67.0040RC32 | LTE interface with Ethernet emulation (no configuration possible), LTE supported bands 42/43 | MiniPCI-e |
NVodafone (Huawei) K4203 | v7.xx | Not supported in ROS v6, but as this modem supports MBIM drivers support will be possible in ROS v7. | Netgear Unite Explore 815S | v6.41 | MIFI unit. No serial support, but works with IP on LTE interface. | USB | Y | LTE |
Novatel USB730L | v6.41RC6 | LTE interface | USB | ? | LTE |
Huawei E3372xxWorks! LTE interface. vendor-id="0x12d1" device-id="0x14dc" There is different versions of this modem available, not all work under RouterOS. Only cdc_ecm and Serial modems are supported. Modem firmware upgrade may be necessary. For ppp mode send AT^SETPORT="FF,12,1,16" data-channel=1 info-channel=0, other modes are explained in modems manual. | USB | Y | LTE | Huawei E8372 | v6.28 | Works! LTE interface only. vendor-id="0x12d1" device-id="0x14db" | USB | ? | LTE |
Telit LE910 | v6.xx | ppp interface, vendorid=0x1bc7 deviceid=0x1201 | MiniPCI-e | ? | LTE |
Quectel EC20/EC21 | v6.xx | ppp interface, there is page in wiki about Quactel: article41RC11 | ppp interface | USB | ? | LTE |
Quectel EC20/EC21 | v6.xx | ppp interface, there is page in wiki about Quectel: article | MiniPCI-e | ? | LTE |
Quectel BG77 | v6.47 | Serial/PPP interface, single AT/modem channel | OEM module | N | IoT |
Quectel BG95-M3 | v6.47 | Serial/PPP interface, single AT/modem channel Will not work in wAP R ac boards. | mini-PCIe | N | 2G/IoT |
Quectel BG96 | v6.45 | Serial/PPP interface, 2x AT/modem channels | mini-PCIe | N | 2G/IoT |
Quectel EC25 | v6.42 | ppp/LTE interface, there is page in wiki about Quectel ppp mode: article RouterOS v6 CDC-ECM mode - LTE interface receive address in modems internal network. RouterOS v7 MBIM mode - LTE interface uses APN IP address. | MiniPCI-e | ? | LTE |
Quectel |
EC25v6.39 | ppp/LTE interface, there is page in wiki about Quactel ppp mode: article | MiniPCI-e | ? | LTE | Quectel EP06 | v6.42 | ppp/LTE interface, there is page in wiki about Quactel: article | MiniPCI-e | ? | LTE |
Huawei E3276-150 | v6.xx | ppp interface | USB | ? | LTE |
ZTE ME3630-E | v6.40RC26 | ppp and LTE interface | MiniPCI-e | ? | LTE |
Jaton MT421e | v6.40RC32 | LTE interface with Ethernet emulation (no configuration possible), LTE supported bands 42/43EG25-G | 6.48.3 | RouterOS v6 CDC-ECM mode - LTE interface receive address in modems internal network. RouterOS v7 MBIM mode - LTE interface uses APN IP address. In some boards may be required to disable SIM hot plug detection: /interface lte set [find] modem-init="AT+QSIMDET=0,1" | MiniPCI-e |
| GSM, 3G, LTE |
Quectel EM12-G | v7.1beta5 | MBIM driver | m.2 | Y | 3G,LTE |
Quectel EP06 | v6.42 | ppp/LTE interface, there is page in wiki about Quectel: article | MiniPCI-e | ? | LTE |
Huawei E5673s-609 | v6.xx | LTE interface | USB | ? | LTE |
Novatel USB730L | v6.41RC6 | LTE interface | USB | ? | LTE |
Alcatel IK40 | v6.41RC11 | LTE interface, Modem can be configured only through modems configuration WEB page. | USB | ? | LTE |
Olivetti Olicard 500 | v6.41RC11 | ppp interface | USB | ? | LTE |
Netgear Unite Explore 815S | v6.41 | MIFI unit. No serial support, but works with IP on LTE interface. | USB | Y | LTE |
R11e-LTE | v6.39.2 | LTE interface. Supports multiple APN passthrough. | MiniPCI-e | Y | LTE |
SXT LTE | v6 | LTE interface. Old version of SXT LTE | Built-in | N | LTE |
SXT LTE kit | v6.42 | LTE interface from R11e-LTE/R11e-LTE-US mini-pcie module | Built-in | Y | LTE |
Quectel UC15 | v6.xx | Works, ppp interface | MiniPCI-e | 3G | Quectel UC20 | v6.xx | Works, ppp interface | MiniPCI-e | 3G | SIMcom SIM5360 | v6.xx | Works! Using PPP interface, vendor-id="0x05c6" device-id="0x9000Quectel RM500Q-GL | v7.1beta6 | MBIM driver | m.2 | Y | 3G, LTE, 5G |
Quectel RM502Q-AE | v7.1beta5 | MBIM driver | m.2 | Y | 3G, LTE, 5G |
Quectel UC15 | v6.xx | Works, ppp interface | MiniPCI-e |
| 3G |
Quectel UC20 | v6.xx | Works, ppp interface | MiniPCI-e |
| 3G |
R11e-LTE | v6.39.2 | LTE interface. Supports multiple APN passthrough. | MiniPCI-e | Y | LTE |
Sierra Netgear AirCard 320U | 6.41 | Customer tested the modem with firmware 03.05.23 | USB | N | LTE |
Sierra wireless MC73xx | v6.xx(ppp) v7.xx (LTE) | Works! PPP interface. And starting with v7.xx it will support LTE interface. MC7304 tested with firmware SWI9X15C_05.05.67.00 | MiniPCI-e | N | LTE |
Sierra Wireless MC7430 | v6.xx and higher | Data channel 2, Info channel 2, Modem init: AT+CGATT=0, Dial-command: AT+CGATT=1;D*99#, also needs 3.0 pins isolated (PINS:23,25,27,31,33) | MiniPCI-e |
| LTE |
Sierra Wireless MC74xx | v7.1 | Basic functionality support for modems with MBIM interface/USB composition | mini-PCIe |
|
|
Sierra Wireless MC7455 | v7.3beta37 | MBIM mode with extended support for USB compositions: - 1009 - diag,modem,mbim
- 100D - diag,nmea,modem,mbim
| mini-PCIe |
|
|
Sierra Wireless MC7710/MC7700/MC7750 | v5.25, v6.0 and 6.40RC43 | If modem uses firmware 3.5 it should be upgraded to 3.5.23.2 firmware release in order to work in RouterOS correctly again. | MiniPCI-e | N | LTE |
SIMcom SIM5360 | v6.xx | Works! Using PPP interface, vendor-id="0x05c6" device-id="0x9000" | MiniPCI-e / USB w/ converter |
| 3G |
SIMcom SIM7100 | v6.xx(ppp) v7.xx (LTE) | Works! PPP interface. And starting with v7.xx it will support LTE interface. vendor-id="0x1e0e" device-id="0x9001" | MiniPCI-e / USB w/ converter |
3G | Huawei E171 | ? | LTE |
SXT LTE | v6 | LTE interface. Old version of SXT LTE | Built-in | N | LTE |
SXT LTE kit | v6. |
xxAnyData ADU-E630WH | v6 | ( aka "USB Wireless HSDPA/UMTS 2.1GHz GSM/GPRS/EGPRS 900/17000MHz/CDMA 1x EVDO Rev.A") | USB | 3G | Ericsson F5521gw | v6.x and higher | MiniPCI-e | 3G | ZTE AC5730 | v6.x | USB | 3G | Huawei E153 | v6.31< and higher | USB | 3G | ZTE MF110 | v6.28 and higher | Set info channel = 2, data channel = 2, Dial command=ATM1L3DT | USB | 3G | ZTE 821D | v6.x | Set Info channel = 1, Data channel = 3, Dial command=ATDT | USB | 3G | Huawei E3531 | v6.24 or 6.40RC25 | There are different versions of this modem E3531-6 works from version 6.40RC25 as ppp, mbim supported only from RouterOS V7 | USB | 3G | Huawei E3351 | v6.24 and higher | USB | 3G | Dell Wireless 5530 HSPA | v6.1 and higher | Data channel 0, Info channel 0, init: AT+CFUN=1 (needs manualy change profile by command AT*ENAP=1,1) | MiniPCI-e | 3G | Telecom NZ T-Stick ZTE MF-181 | v6.0rc13 | Data Channel=2, Info Channel=2, APN internet.telecom.co.nz, PHONE=*99#. Tested ok for both data and SMS on CCR1016-12G | USB | 3G | Sierra Wireless MC7430 | v6.xx and higher | Data channel 2, Info channel 2, Modem init: AT+CGATT=0, Dial-command: AT+CGATT=1;D*99#, also needs 3.0 pins isolated (PINS:23,25,27,31,33) | MiniPCI-e | LTE | Sierra Netgear AirCard 320U | 6.41 | Customer tested the modem with firmware 03.05.23 | USB | N | LTE |
Huawei e398 | v6.xx and higher | ppp interface | USB | LTE | Huawei e3131 | v6.xx and higher | ppp interface | USB | 3G | ZTE MF90 | v6.44beta32 and higher | LTE interface | USB | N | LTE |
Telit LM940 | v6.44 | LTE interface in some cases needs 3.0 pins isolated (PINS:23,25,27,29,31,33) | MiniPCI-e | Y | LTE |
Telit LM960 | v6.46 | LTE interface in some cases needs 3.0 pins isolated (PINS:23,25,27,29,31,33) | MiniPCI-e | Y | LTE |
Works! ppp interface, vendorid=0x12d1 deviceid=0x140c | USB | 3G | D-link DWM-157 | v6.xx | Works! Data Channel: 2, Info Channel: 3,Modem Init: AT+CFUN=1, vendor-id="0x2001" device-id="0x7d02" Some info from modem: > H/W Ver.: B1, F/W Ver.: 2.0.1eu, revision: +CGMR: MOLY.WR8.W1231.DC.WG.MP.V3, 2013/04/09 02:08 Different HW revisions might not work with RouterOS | USB | 3G | LTE interface from R11e-LTE/R11e-LTE-US mini-pcie module | Built-in | Y | LTE |
Tele2.ru LTE-D402 | v6.47 | Config-less LTE interface |
| N |
|
Telecom NZ T-Stick ZTE MF-181 | v6.0rc13 | Data Channel=2, Info Channel=2, APN internet.telecom.co.nz, PHONE=*99#. Tested ok for both data and SMS on CCR1016-12G | USB |
| 3G |
Telit FN980m | v7.5 | AT#USBCFG=2 | m.2 |
| LTE, 5G |
Telit LE910 | v6.xx | ppp interface, vendorid=0x1bc7 deviceid=0x1201 | MiniPCI-e | ? | LTE |
Telit LE910C1 | v6.46 | Non-configurable from RouterOS | MiniPCI-e |
| LTE |
Telit LM940 | v6.44 | LTE interface in some cases needs 3.0 pins isolated (PINS:23,25,27,29,31,33) | MiniPCI-e | Y | LTE |
Telit LM960 | v6.46 | LTE interface in some cases needs 3.0 pins isolated (PINS:23,25,27,29,31,33) | MiniPCI-e | Y | LTE |
TPS (Turning Point Solution) GCT450 | v6.48 | Config-less LTE interface | MiniPCI-e | N |
|
Vodafone (Huawei) K4203 | v7.xx | Not supported in ROS v6, but as this modem supports MBIM drivers support will be possible in ROS v7. | USB | ? | LTE |
Vodafone K4201-Z | v6.8 | Some settings are ignored. LTE interface. | USB | ? | LTE |
Vodafone K4305 | v6.7 | Some settings are ignored. | USB | ? | LTE |
Vodafone K5160 | v6.37 | Some settings are ignored. | USB | ? | LTE |
Yota LU150 | v5.22 and v6.4 | Some settings are ignored. Works in Russian markets. | USB | ? | LTE |
Yota wifi modem | v6.7 | Some settings are ignored. Works in Russian markets. | USB | ? | LTE |
Yota WLTUBA-107 | v6.0 | Some settings are ignored. Works in Russian markets. | USB | ? | LTE |
ZTE 821D | v6.x | Set Info channel = 1, Data channel = 3, Dial command=ATDT | USB |
| 3G |
ZTE AC5730 | v6.x |
| USB |
| 3G |
ZTE ME3630-E | v6.40RC26 | ppp and LTE interface | MiniPCI-e | ? | LTE |
ZTE MF110 | v6.28 and higher | Set info channel = 2, data channel = 2, Dial command=ATM1L3DT | USB |
| 3G |
ZTE MF823 | v6.8 | Some settings are ignored. For some devices it's needed to enter in FACTORY mode to change operating state. | USB | ? | LTE |
ZTE MF825A | v6.xx | Some settings are ignored. | USB | ? | LTE |
ZTE MF827 | v6.8 | Some settings are ignored. | USB | ? | LTE |
ZTE MF90 | v6.44beta32 and higher | LTE interface | USB | N | LTE |
Anteniti 3372h-153 |
|
|
|
|
|
For some modems with USB3.0 support in some cases USB3.0 pins need to be isolated to ensure correct initialization:
...