...
This article describes supported add-on peripherals for RouterBOARD hardware devices.
Cellular modems
Model | vendor-id | device-id | Tested RouterOS version | Comments | Format |
---|
Passthrough support | Technologies | Alcatel IK40 |
|
| v6.41RC11 | LTE interface, Modem can be configured only through modems configuration WEB page. | USB |
N | LTE |
Alcatel IK41 |
|
| v6.48 | Config-less LTE interface | USB |
NLTE | Android usb tethering interface |
|
| v6.7 | Some settings are ignored. | USB |
? | LTE | AnyData ADU-E630WH |
|
| v6 | ( aka "USB Wireless HSDPA/UMTS 2.1GHz GSM/GPRS/EGPRS 900/17000MHz/CDMA 1x EVDO Rev.A") | USB |
3G |
Anteniti 3372h-153 |
|
| 7.12 |
| USB |
BandRich C501 |
|
| v5.25 and v6.0 |
| USB |
? | LTE | Huawei e398 | v6.xx and higher | ppp interface | USB | LTE | Huawei E5377 | v6.36.1 | MIFI unit. No serial support, but works with IP on LTE interface | USB | ? | LTE |
Huawei E5673s-609 | v6.xx | LTE interface | USB | ? | LTE |
Huawei E8372 | v6.28 | Works! LTE interface only. vendor-id="0x12d1" device-id="0x14db" | USB | ? | LTE |
Huawei ME909s-120 | v6.28 | Recommended modem firmware version 11.617.24.00.00 To reduce LTE interface IP subnet mask to /32 configure modem with at-chat command: /interface lte at-chat [find] input="AT^CUSTFEATURE=3,1" | MiniPCI-e | Y | LTE |
Huawei ME909u-521 | v6.11 | MiniPCI-e | N | LTE | Huawei MU609 | v6.11 | MiniPCI-e | ? | 3G | Huawei MU709s-2 | v6.28 | MiniPCI-e | Y | 3G | Jaton MT421e | v6.40RC32 | LTE interface with Ethernet emulation (no configuration possible), LTE supported bands 42/43 | MiniPCI-e | ? | LTE |
Netgear Unite Explore 815S | v6.41 | MIFI unit. No serial support, but works with IP on LTE interface. | USB | Y | LTE |
Novatel USB730L | v6.41RC6 | LTE interface | USB | ? | LTE |
Olivetti Olicard 500 | v6.41RC11 | ppp interface | USB | ? | LTE |
Quectel EC20/EC21 | v6.xx | ppp interface, there is page in wiki about Quectel: article | MiniPCI-e | ? | LTE |
Quectel EC25 | v6.39 | ppp/LTE interface, there is page in wiki about Quectel ppp mode: article | MiniPCI-e | ? | LTE |
Quectel EG25-G | 6.48.3 | ECM driver. Also supported in RouterOS v7 with MBIM dirver. | MiniPCI-e | GSM, 3G, LTE | Quectel EM12-G | D-link DWM-157 | 0x2001 | 0x7d02 | v6.xx | Works! Data Channel: 2, Info Channel: 3,Modem Init: AT+CFUN=1, vendor-id="0x2001" device-id="0x7d02" Some info from modem: > H/W Ver.: B1, F/W Ver.: 2.0.1eu, revision: +CGMR: MOLY.WR8.W1231.DC.WG.MP.V3, 2013/04/09 02:08 Different HW revisions might not work with RouterOS | USB |
3G | Dell Wireless 5530 HSPA | v6.1 and higher | Data channel 0, Info channel 0, init: AT+CFUN=1 (needs manualy change profile by command AT*ENAP=1,1) | MiniPCI-e | 3G | Ericsson F5521gw | v6.x and higher | MiniPCI-e | 3G | Fibocom FM150-AE | v7.1beta5 | MBIM driver. Revision: 89603.1000.00.01.01.03 | M.2 | 3G, LTE, 5G | Fibocom NL-952-EAU | v7.1beta5 | MBIM driver. Revision: 19600.7000.00.04.01.05 | M.2 | 3G, LTE | Huawei E153 | v6.31< and higher | USB | 3G | Huawei E171 | v6.xx | Works! ppp interface, vendorid=0x12d1 deviceid=0x140c | USB | 3G | Huawei e3131 | v6.xx and higher | ppp interface | USB | 3G | Huawei E3272 | v6.8 | Some settings are ignored. There are multiple versions of this modem. Looks like only modem with device-id="0x14db" works as LTE interface. | USB | ? | LTE |
Huawei E3276-150 | v6.xx | ppp interface | USB | ? | LTE |
Huawei E3351 | v6.24 and higher | USB | 3G | HUAWEI E3372H-320 | v7.xx | Incompatibility issues in RouterOS v6 with all -320 Huawei modems. Works in RouterOS v7. | USB | N | LTE |
Huawei E3531 | v6.24 or 6.40RC25 | There are different versions of this modem E3531-6 works from version 6.40RC25 as ppp, mbim supported only from RouterOS V7 | USB | 3G | D-link DWM-222 |
|
| v6.38 | Multiple modem versions with same marketing name exist, only H/W ver: A1 supported as config-less LTE interface | USB |
Dell DW5821e |
|
| v7.4beta4 and higher | MBIM driver. Revision: T77W968.F1.0.0.5.2.VZ.013 044 | M.2 |
Dell DW5821e-eSIM | 0x413c | 0x81e0 | 7.11 and higher | MBIM driver. FW: T77W968.F1.0.0.5.2.GC.013. "at-chat" support added | M.2 |
Dell Wireless 5530 HSPA |
|
| v6.1 and higher | Data channel 0, Info channel 0, init: AT+CFUN=1 (needs manualy change profile by command AT*ENAP=1,1) | MiniPCI-e |
Ericsson F5521gw |
|
| v6.x and higher |
| MiniPCI-e |
Fibocom FM150-AE | 0x2cb7 | 0x0111 | v7.1beta5 | MBIM driver. Revision: 89603.1000.00.01.01.03 | M.2 |
Fibocom NL-952-EAU |
|
| v7.1beta5 | MBIM driver. Revision: 19600.7000.00.04.01.05 | M.2 |
Marvell PXA1802 based modems | 0x1286 | 0x4e31 | v7.2.2 |
| mini-PCIe |
Huawei E153 |
|
| v6.31< and higher |
| USB |
Huawei E171 |
|
| v6.xx | Works! ppp interface, vendorid=0x12d1 deviceid=0x140c | USB |
Huawei e3131 |
|
| v6.xx and higher | ppp interface | USB |
Huawei E3372h, E5576h, E8372h | 0x12d1 | 0x14db | v6.8 | Config-less LTE interface for modems with vendor-id="0x12d1" device-id="0x14db" Models with suffixes -320 and -608 will not work with RouterOS v6, please use v7 instead Models with suffixes -325 works only with arm cpu | USB |
Huawei E3276-150 |
|
| v6.xx | ppp interface | USB |
Huawei E3351 |
|
| v6.24 and higher |
| USB |
Huawei E3531 |
|
| v6.24 or 6.40RC25 | There are different versions of this modem E3531-6 works from version 6.40RC25 as ppp, mbim supported only from RouterOS V7 | USB |
Huawei e398 |
|
| v6.xx and higher | ppp interface | USB |
Huawei E5377 |
|
| v6.36.1 | MIFI unit. No serial support, but works with IP on LTE interface | USB |
Huawei E5673s-609 |
|
| v6.xx | LTE interface | USB |
Huawei K5160 |
|
| v6.37 v7.0beta6 | v6 and v7 - config-less LTE interface v7 - by default will try to use modem in MBIM mode | USB |
Huawei K5161 |
|
| v6.47 | Config-less LTE interface | USB |
Huawei ME909s-120 |
|
| v6.28 | Recommended modem firmware version 11.617.24.00.00 To reduce LTE interface IP subnet mask to /32 configure modem with at-chat command: /interface lte at-chat [find] input="AT^CUSTFEATURE=3,1" | MiniPCI-e |
Huawei ME909u-521 |
|
| v6.11 |
| MiniPCI-e |
Huawei MU609 |
|
| v6.11 |
| MiniPCI-e |
Huawei MU709s-2 |
|
| v6.28 |
| MiniPCI-e |
Huawei MS2372h-517 |
|
| v7.12beta3 | ppp/serial interface | USB |
Jaton MT421e |
|
| v6.40RC32 | LTE interface with Ethernet emulation (no configuration possible), LTE supported bands 42/43 | MiniPCI-e |
Netgear Unite Explore 815S |
|
| v6.41 | MIFI unit. No serial support, but works with IP on LTE interface. | USB |
Novatel USB730L |
|
| v6.41RC6 | LTE interface | USB |
Olivetti Olicard 500 |
|
| v6.41RC11 | ppp interface | USB |
Quectel EC20/EC21 |
|
| v6.xx | ppp interface, there is page in wiki about Quectel: article | MiniPCI-e |
Quectel BG77 | 0x2c7c | 0x0700 | v6.47 | Serial/PPP interface, single AT/modem channel | OEM module |
Quectel BG95-M3 |
|
| v6.47 | Serial/PPP interface, single AT/modem channel Will not work in wAP R ac boards. | mini-PCIe |
Quectel BG96 |
|
| v6.45 | Serial/PPP interface, 2x AT/modem channels | mini-PCIe |
Quectel EC25-EU | 0x2c7c | 0x0125 | v6.42 | ppp/LTE interface, there is page in wiki about Quectel ppp mode: article RouterOS v6 CDC-ECM mode - LTE interface receive address in modems internal network. RouterOS v7 MBIM mode - LTE interface uses APN IP address. | MiniPCI-e |
Quectel EG25-G | 0x2c7c | 0x0125 | 6.48.3 | RouterOS v6 CDC-ECM mode - LTE interface receive address in modems internal network. RouterOS v7 MBIM mode - LTE interface uses APN IP address. In some boards may be required to disable SIM hot plug detection: /interface lte set [find] modem-init="AT+QSIMDET=0,1" | MiniPCI-e |
Quectel EM12-G | 0x2c7c | 0x0512 |
Y | 3G,LTE | Quectel EP06 |
|
| v6.42 | ppp/LTE interface, there is page in wiki about Quectel: article | MiniPCI-e |
? | LTE |
Quectel RM500Q-GL | 0x2c7c | 0x0800 | v7.1beta6 | MBIM driver | m.2 |
Y | Quectel RM500Q-AE | 0x2c7c | 0x0800 | v7.1beta6 | MBIM driver | m.2 |
3G, LTE, 5G |
Quectel RM502Q-AE | 0x2c7c | 0x0800 | v7.1beta5 | MBIM driver | m.2 |
Y | |
Quectel RM510Q-GL | 0x2c7c | 0x0800 | 7.9 | MBIM driver | m.2 |
3G, LTE, 5G |
Quectel UC15 |
|
| v6.xx | Works, ppp interface | MiniPCI-e |
3G | Quectel UC20 |
|
| v6.xx | Works, ppp interface | MiniPCI-e |
3G |
R11e-4G | 0x2cd2 | 0x0003 | v6.42 | LTE interface. Supports multiple APN passthrough. | MiniPCI-e |
R11e- |
LTELTE6 | 0x2cd2 | 0x0004 | v6.39.2 | LTE interface. Supports multiple APN passthrough. | MiniPCI-e |
Y | LTE | R11e-LTE | 0x2cd2 | 0x0001 | v6.39.2 | LTE interface. Supports multiple APN passthrough. | MiniPCI-e |
Sierra Netgear AirCard 320U |
|
| 6.41 | Customer tested the modem with firmware 03.05.23 | USB |
N | LTE | Sierra wireless MC73xx |
|
| v6.xx(ppp) v7.xx (LTE) | Works! PPP interface. And starting with v7.xx it will support LTE interface. MC7304 tested with firmware SWI9X15C_05.05.67.00 | MiniPCI- |
eN | LTEe |
Sierra Wireless MC7430 |
|
| v6.xx and higher | Data channel 2, Info channel 2, Modem init: AT+CGATT=0, Dial-command: AT+CGATT=1;D*99#, also needs 3.0 pins isolated (PINS:23 |
,25,27,31,33),25,27,31,33) | MiniPCI-e |
Sierra Wireless MC74xx |
|
| v7.1 | Basic functionality support for modems with MBIM interface/USB composition | mini-PCIe |
Sierra Wireless MC7455 |
|
| v7.3beta37 | MBIM mode with extended support for USB compositions: - 1009 - diag,modem,mbim
- 100D - diag,nmea,modem,mbim
| mini-PCIe |
MiniPCI-e | LTE |
Sierra Wireless MC7710/MC7700/MC7750 |
|
| v5.25, v6.0 and 6.40RC43 | If modem uses firmware 3.5 it should be upgraded to 3.5.23.2 firmware release in order to work in RouterOS correctly again. | MiniPCI-e |
N | LTE |
SIMcom SIM5360 |
|
| v6.xx | Works! Using PPP interface, vendor-id="0x05c6" device-id="0x9000" | MiniPCI-e / USB w/ converter |
3G | SIMcom SIM7100 | 0x1e0e | 0x9001 | v6.xx(ppp) v7.xx (LTE) | Works! PPP interface. And starting with v7.xx it will support LTE interface. |
vendor-id="0x1e0e" device-id="0x9001" | MiniPCI-e / USB w/ converter |
? | SIMCom SIM8202G-M.2 |
|
| v7.11 | MBIM driver supported: AT+CUSBCFG=usbid,1e0e,901e | m.2 |
LTESXT LTE kit | v6.42 | LTE interface from R11e-LTE/R11e-LTE-US mini-pcie module | Built-in | Y | LTE |
|
SXT LTE |
|
| v6 | LTE interface. Old version of SXT LTE | Built-in |
N | LTE | Tele2.ru LTE-D402 |
|
| v6.47 | Config-less LTE interface |
|
Telecom NZ T-Stick ZTE MF-181 |
|
| v6.0rc13 | Data Channel=2, Info Channel=2, APN internet.telecom.co.nz, PHONE=*99#. Tested ok for both data and SMS on CCR1016-12G | USB |
3GTelit FN980m |
|
| v7.5 | AT#USBCFG=2 | m.2 |
Telit LE910 | 0x1bc7 | 0x1201 | v6.xx | ppp interface |
, vendorid=0x1bc7 deviceid=0x1201? | LTE |
Telit LE910C1 |
|
| v6.46 | Non-configurable from RouterOS | MiniPCI-e |
LTE |
Telit LM940 |
|
| v6.44 | LTE interface in some cases needs 3.0 pins isolated (PINS:23,25,27,29,31,33) | MiniPCI-e |
Y | LTE | Telit LM960 |
|
| v6.46 | LTE interface in some cases needs 3.0 pins isolated (PINS:23,25,27,29,31,33) | MiniPCI-e |
Y | LTE | TPS (Turning Point Solution) GCT450 |
|
| v6.48 | Config-less LTE interface | MiniPCI-e |
Vodafone (Huawei) K4203 |
|
| v7.xx | Not supported in ROS v6, but as this modem supports MBIM drivers support will be possible in ROS v7. | USB |
? | LTE | Vodafone K4201-Z |
|
| v6.8 | Some settings are ignored. LTE interface. | USB |
? | LTE |
Vodafone K4305 |
|
| v6.7 | Some settings are ignored. | USB |
?LTE | Vodafone K5160 |
|
| v6.37 | Some settings are ignored. | USB |
? | LTE | Yota LU150 |
|
| v5.22 and v6.4 | Some settings are ignored. |
Works in Russian markets.? | LTE |
Yota wifi modem |
|
| v6.7 | Some settings are ignored. |
Works in Russian markets.?LTE | Yota WLTUBA-107 |
|
| v6.0 | Some settings are ignored. |
Works in Russian markets.?LTE | ZTE 821D |
|
| v6.x | Set Info channel = 1, Data channel = 3, Dial command=ATDT | USB |
3G | 3G |
ZTE ME3630-E |
|
| v6.40RC26 | ppp and LTE interface | MiniPCI-e |
? | LTE | ZTE MF110 |
|
| v6.28 and higher | Set info channel = 2, data channel = 2, Dial command=ATM1L3DT | USB |
3G |
ZTE MF823 |
|
| v6.8 | Some settings are ignored. For some devices it's needed to enter in FACTORY mode to change operating state. | USB |
? | LTE |
ZTE MF825A |
|
| v6.xx | Some settings are ignored. | USB |
? | LTE | ZTE MF827 |
|
| v6.8 | Some settings are ignored. | USB |
? | ZTE MF832S |
|
| v7.10 | Config-less support, may require to set some settings using at-chat or modem init string | USB |
LTE |
ZTE MF90 |
|
| v6.44beta32 and higher | LTE interface | USB |
NLTE |
Note |
---|
Not all modems are listed. Localized and locked units may have compatibility issues. All modems using MBIM driver should work by default on RouterOS v7. |
For some modems with USB3.0 support in some cases USB3.0 pins need to be isolated to ensure correct initialization:
...